08-24-2019 06:49 PM
Here is my Network,
Have a VLAN in a switch which was connected to a Router which does BGP. If i use static route on my switch to send traffic to BGP router. I am able to ping VLAN interface ip address from other end also, i am able to ping from my end. But if I use route-map to match the traffic from my lan to send to BGP route using set ip next-hop BGP route IP or set ip default next-hop BGP route IP. Ping from my end to other end work fine. But from my other end to my end drops at my BGP router.
08-24-2019 07:22 PM
08-24-2019 08:57 PM
Thanks very much for the quick reply.
Here is my Switch Config.
route-map GET permit 10
match policy-list GET_LAN
set ip next-hop 192.168.200.1
sh ip access-lists GET_LAN
Extended IP access list GET_LAN
10 permit ip 10.30.110.0 0.0.0.255 10.0.23.0 0.0.0.255
20 permit ip 10.30.110.0 0.0.0.255 10.1.10.0 0.0.0.255
30 permit ip 10.30.110.0 0.0.0.255 10.1.13.0 0.0.0.255
sh running-config interface vlan 110
Building configuration...
Current configuration : 94 bytes
!
interface Vlan110
ip address 10.30.110.1 255.255.255.0
ip policy route-map GET
end
BGP config
router bgp 65xx
bgp log-neighbor-changes
network 10.30.110.0 mask 255.255.255.0
network 192.168.200.0 mask 255.255.255.252
redistribute static
neighbor 10.xx.x.22 remote-as 21326
neighbor 10.xx.x.22 update-source GigabitEthernet0/0
neighbor 10.xx.x.22 soft-reconfiguration inbound
sh ip bgp neighbors 10.xxx.x.22 received-routes
BGP table version is 9, local router ID is 192.168.200.1
Status codes: s suppressed, d damped, h history, * valid, > best, i - internal,
r RIB-failure, S Stale, m multipath, b backup-path, f RT-Filter,
x best-external, a additional-path, c RIB-compressed,
Origin codes: i - IGP, e - EGP, ? - incomplete
RPKI validation codes: V valid, I invalid, N Not found
Network Next Hop Metric LocPrf Weight Path
*> 10.0.23.0/24 10.254.1.22 0 21326 13979 65005 i
*> 10.1.10.0/24 10.254.1.22 0 21326 13979 65005 i
*> 10.1.13.0/24 10.254.1.22 0 21326 13979 65005 i
*> 10.254.1.12/30 10.254.1.22 0 21326 13979 65005 i
r> 10.254.1.20/30 10.254.1.22 0 0 21326 i
*> 192.168.1.0/30 10.254.1.22 0 0 21326 i
sh ip bgp neighbors 10.xxx.x.22 advertised-routes
BGP table version is 9, local router ID is 192.168.200.1
Status codes: s suppressed, d damped, h history, * valid, > best, i - internal,
r RIB-failure, S Stale, m multipath, b backup-path, f RT-Filter,
x best-external, a additional-path, c RIB-compressed,
Origin codes: i - IGP, e - EGP, ? - incomplete
RPKI validation codes: V valid, I invalid, N Not found
Network Next Hop Metric LocPrf Weight Path
*> 10.30.110.0/24 192.168.200.2 0 32768 i
*> 192.168.200.0/30 0.0.0.0 0 32768 i
Total number of prefixes 2
If i add a static route on my switch "ip route 10.0.23.0 255.255.255.0 192.168.200.1" only then i am able to ping 10.30.110.1 from remote end.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: