cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
7885
Views
0
Helpful
7
Replies

txload 255/255 but no traffic

krutibasa majhi
Level 1
Level 1

Hi all,

I am experiencing a strange problem with a ASR1002 router that I just  installed.thsi is a point to point link .the link is working  but for  some reason the txload on interface g0/0/0 show 255/255 even though  there is no traffic going over to this router.

Thanks in advance for any suggestions !!!

Please see the below interface status for both router.

Router#sh int gi0/0/3

GigabitEthernet0/0/3 is up, line protocol is up

  Hardware is 4XGE-BUILT-IN, address is a493.4c98.db03 (bia a493.4c98.db03)

  Description: "100Mbps LINK"

  Internet address is 10.172.20.110/30

  MTU 9100 bytes, BW 100000 Kbit/sec, DLY 100 usec,

     reliability 255/255, txload 255/255, rxload 1/255

  Encapsulation ARPA, loopback not set

  Keepalive not supported

  Full Duplex, 100Mbps, link type is auto, media type is T

  output flow-control is on, input flow-control is on

  ARP type: ARPA, ARP Timeout 04:00:00

  Last input 00:46:49, output 00:00:29, output hang never

  Last clearing of "show interface" counters never

  Input queue: 0/375/0/0 (size/max/drops/flushes); Total output drops: 0

  Queueing strategy: fifo

  Output queue: 0/40 (size/max)

  5 minute input rate 7000 bits/sec, 4 packets/sec

  5 minute output rate 5000 bits/sec, 2 packets/sec

     17890 packets input, 9074660 bytes, 0 no buffer

     Received 0 broadcasts (0 IP multicasts)

     0 runts, 0 giants, 0 throttles

     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored

     0 watchdog, 7503 multicast, 0 pause input

     10137 packets output, 2803120 bytes, 0 underruns

     0 output errors, 0 collisions, 2 interface resets

     0 unknown protocol drops

     0 babbles, 0 late collision, 0 deferred

     0 lost carrier, 0 no carrier, 0 pause output

     0 output buffer failures, 0 output buffers swapped out

Router#

-------------------------------------------------------------------------------------------------------------------------------------------------------------

RP/0/RSP0/CPU0:ASR-9010#sh int Gi0/0/0/13

Tue Oct 30 11:32:10.104 ist

GigabitEthernet0/0/0/13 is up, line protocol is up

  Interface state transitions: 11

  Hardware is GigabitEthernet, address is 18ef.63e8.6ce7 (bia 18ef.63e8.6ce7)

  Description: "100Mbps , Gi0/0/0/13"

  Internet address is 10.172.20.109/30

  MTU 9114 bytes, BW 100000 Kbit (Max: 100000 Kbit)

     reliability 253/255, txload 0/255, rxload 0/255

  Encapsulation ARPA,

  Full-duplex, 100Mb/s, THD, link type is force-up

  output flow control is off, input flow control is off

  loopback not set,

  ARP type ARPA, ARP timeout 04:00:00

  Last input 00:00:00, output 00:00:00

  Last clearing of "show interface" counters 22w6d

  30 second input rate 3000 bits/sec, 0 packets/sec

  30 second output rate 8000 bits/sec, 3 packets/sec

     665819 packets input, 159562042 bytes, 5896 total input drops

     1 drops for unrecognized upper-level protocol

     Received 21 broadcast packets, 99558 multicast packets

              350 runts, 1154 giants, 0 throttles, 0 parity

     5895 input errors, 2545 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

     2154457 packets output, 748147945 bytes, 0 total output drops

     Output 14647 broadcast packets, 1490193 multicast packets

     0 output errors, 0 underruns, 0 applique, 0 resets

     0 output buffer failures, 0 output buffers swapped out

     11 carrier transitions

RP/0/RSP0/CPU0:ASR-9010#

3 Accepted Solutions

Accepted Solutions

Rahul Kukreja
Level 1
Level 1

This is due to the known defect -

CSCtw90305   

Show interface X/Y returns output with counter txload 255/255

which was duplicated to CSCtr15153

Please use the Bug Tool Kit and verify your the IOS is affected or not.

http://tools.cisco.com/Support/BugToolKit/action.do?hdnAction=searchBugs

- HTH

  Rahul

View solution in original post

Leo Laohoo
Hall of Fame
Hall of Fame

I agree with Rahul.  This is a bug.  This bug was fixed on IOS version 15.2(2)S (aka 3.6.0).

View solution in original post

ASIC Post initialization failed

Hardware failure.  There's nothing you can do about it except contact Cisco TAC and have the ME3800X RMA-ed.

View solution in original post

7 Replies 7

Rahul Kukreja
Level 1
Level 1

This is due to the known defect -

CSCtw90305   

Show interface X/Y returns output with counter txload 255/255

which was duplicated to CSCtr15153

Please use the Bug Tool Kit and verify your the IOS is affected or not.

http://tools.cisco.com/Support/BugToolKit/action.do?hdnAction=searchBugs

- HTH

  Rahul

Thanks BOSS it working

Leo Laohoo
Hall of Fame
Hall of Fame

I agree with Rahul.  This is a bug.  This bug was fixed on IOS version 15.2(2)S (aka 3.6.0).

BOSS you are right .after upgrade it working.

thanks

I found a new problem in a new L3  Switch ME 3800X. It repeatedly restarts while I am swiching it on.  Through the consol its showing errors after flash initialization. If Im  breaking the operation it redirects it to switch prompt (switch:).

Errors:

1.Asic1, PB0 Training Failed.

2.ASIC Post initialization failed

3.driver class subsystem initialization failed

If anyone has a solution please help me.

ASIC Post initialization failed

Hardware failure.  There's nothing you can do about it except contact Cisco TAC and have the ME3800X RMA-ed.

Finally today  i logged in Cisco TAC

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: