07-20-2006 12:59 PM - edited 03-03-2019 01:24 PM
Hello,
My task is to upgrade the IOS to 12.2(18)SXF4 size 75MB.
1. Do we have to upgrade both the SUP720 and the MSFC flash SEPERATELY with new IOS?
Please advise.
--------------------------------
D000RTR01#sho mod
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 24 CEF720 24 port 1000mb SFP WS-X6724-SFP SAD083700XX
5 2 Supervisor Engine 720 (Active) WS-SUP720-BASE SAD0834001U
6 2 Supervisor Engine 720 (Warm) WS-SUP720-BASE SAD0834088X
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
1 0011.bb6b.1398 to 0011.bb6b.13af 2.1 12.2(14r)S5 12.2(18)SXD6 Ok
5 000f.f7be.cf7c to 000f.f7be.cf7f 3.1 7.7(1) 12.2(18)SXD6 Ok
6 000f.f7be.ceb8 to 000f.f7be.cebb 3.1 7.7(1) 12.2(18)SXD6 Ok
Mod Sub-Module Model Serial Hw Status
--- --------------------------- ------------------ ------------ ------- -------
1 Centralized Forwarding Card WS-F6700-CFC SAD082807PY 2.0 Ok
5 Policy Feature Card 3 WS-F6K-PFC3A SAD082500V3 2.3 Ok
5 MSFC3 Daughterboard WS-SUP720 SAD08300FKE 2.2 Ok
6 Policy Feature Card 3 WS-F6K-PFC3A SAD082604A4 2.3 Ok
6 MSFC3 Daughterboard WS-SUP720 SAD08300FHD 2.2 Ok
Mod Online Diag Status
--- -------------------
1 Pass
5 Pass
6 Pass
D000RTR01#sho mod ver
Mod Port Model Serial # Versions
--- ---- ------------------ ----------- --------------------------------------
1 24 WS-X6724-SFP SAD083700XX Hw : 2.1
Fw : 12.2(14r)S5
Sw : 12.2(18)SXD6
Sw1: 8.4(0.61)RCC9
WS-F6700-CFC SAD082807PY Hw : 2.0
5 2 WS-SUP720-BASE SAD0834001U Hw : 3.1
Fw : 7.7(1)
Sw : 12.2(18)SXD6
Sw1: 8.4(0.61)RCC9
WS-SUP720 SAD08300FKE Hw : 2.2
Fw : 12.2(14r)S9
Sw : 12.2(18)SXD6
WS-F6K-PFC3A SAD082500V3 Hw : 2.3
6 2 WS-SUP720-BASE SAD0834088X Hw : 3.1
Fw : 7.7(1)
Sw : 12.2(18)SXD6
Sw1: 8.4(0.61)RCC9
WS-SUP720 SAD08300FHD Hw : 2.2
Fw : 12.2(14r)S9
Sw : 12.2(18)SXD6
WS-F6K-PFC3A SAD082604A4 Hw : 2.3
D000RTR01#
D000RTR01#sho ver
Cisco Internetwork Operating System Software
IOS (tm) s72033_rp Software (s72033_rp-PSV-M), Version 12.2(18)SXD6, RELEASE SOF
TWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Wed 17-Aug-05 17:34 by evmiller
Image text-base: 0x4002100C, data-base: 0x42040000
ROM: System Bootstrap, Version 12.2(14r)S9, RELEASE SOFTWARE (fc1)
BOOTLDR: s72033_rp Software (s72033_rp-PSV-M), Version 12.2(18)SXD6, RELEASE SOF
TWARE (fc1)
---
65536K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x2102
D000RTR01#
07-24-2006 10:00 AM
No,
You assumning your running native IOS, you should be able to load the image on SUP-A and SUP-B change the bootparameter to reflect the new image name.
Then force a failover, Insure that SUP-A boots normaly then force a second failover to upgrade SUP-B.
This is assuming your running redundancy mode.
Hope that helps
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: