Anyone is preparing ccie service provider lab. I am looking for group where we can collaborate our study discussion so we can exchange our concepts and it helps definitely to boost preparation.Keep learning...
Forum Posts
i have had the system i have in place for some time and had no problems, when using a 2 router approach [isp1 and isp2] but since i merged both onto 1 device, ISRC111 there is an issue with incoming connections via isp1. i am using the same acl's and...
Dear All , After having the old faithful 5515 on guard I am trying to migrate to a vFMC with a NGFW. Many issues arise with S2S and bugs in the GUI , BUT I am experiencing an other issue with a simple port forwarding. I have the same ACL - source out...
Hi, I have 4 multicast sources sending traffic each to two multicast groups, as follows: 10.65.190.1 -> 224.64.64.110.65.190.1 -> 224.64.64.510.65.190.2 -> 224.64.64.110.65.190.2 -> 224.64.64.5 The traffic enters the router via a VLAN interface con...
Hi Community,I have added the SFP module "SFP-10G-SR-S" to my C8355-G2 router,however when i tried to setup the ip address on it it does not give me ip address command. I tried to make that port with layer using no switchport command but still no luc...
Hi i have this pathAdvertised path-id 1Path type: external, path is valid, is best path, no labeled nexthop, in ribAS-Path: 208555 , path sourced external to AS172.18.14.238 (metric 0) from 185.217.6.34 (192.168.20.1)Origin incomplete, MED not set, l...
I learned that MED is applied to outbound updates , dictating the best inbound traffic into the AS, but I saw the vice-versa is also true like you can apply med for indbound updates also and it works the same right??
Hi , am trying to advertise default Mgmt-Vrf route to GRT so that other devices reachable to default route . thanks for tips and tricks . Configuration is mentioned below . DC01-leaf03-55#show run int giga0/0interface GigabitEthernet0/0vrf forwardin...
I desire to setup multiple parallel GREoIPSec connections from a single router WAN interface IP to multiple remote sites. I know that I can achieve this by applying to the interface a crypto map that is defined in multiples with different sequence nu...
Resolved! BGP setup for spine and leaf
Hi GuysWhat is the typical and recommended BGP setup for typical spine and leaf networks, would it be EBGP between the spine and leafs? would each leaf be in the same or a different ASN than the other leaf? would you peer with loopacks?would it load ...
Hi GuysI need to purchase 2 routers for a large site, the site will have up to a 1Gig MPLS linked to each of the routers.I was looking at the C8300-1N1S-6T, however the later series has appeared to come out, the alternative model was the C8235-E-G2Th...
Hello I had trtied to apply this scenario to my FPR1010 but either due to lack of understand or simply did not fit my needs, I decided the FPR1010 was a Firewall {obviously) and decided to let it be such and work on the ISRC1111. What I have posted b...
So I read this on official cisoc routing and switchin route 300-101 "Cisco IOS lists a null value for Local_Pref for eBGP-learned routes by default" , but I saw in my lab that the local preference is not null it's 100. What it means??
Greetings I have a N540-24Z8Q2C-M and start receiving log message from OBFL flash 0/RP0/ADMIN0:Dec 17 14:12:57.777 AST: mediasvr[2623]: %MEDIASVR-MEDIASVR-4-OBFL_FLASH_ACCESS_FAILED : OBFL flash access failed, error : Read-only file system0/RP0/ADMI...
Network scenario: ISP>CISCO Router> CISCO FTD > Core SW >Access SW > Serverwe have two public ip like 203.76.64.16/28 and like 203.76.64.64/26 here only 203.76.64.19 is my end and also 203.76.64.64/26 is used for only one to one NAT in FTD for my few...
