06-20-2012 11:36 PM - edited 03-04-2019 04:44 PM
I'm trying to get a PPPoE config working on an 1841. Running c1841-advsecurityk9-mz.124-3i.bin . I tried c1841-advsecurityk9-mz.151-4.M4.bin but it has even less protocol options.
I used a walkthrough but it suggests the following fragment which doesn't work because there is no "protocol ppoe" command available on my system. Perhaps there is a simpler way to do this? I tried c1841-broadband-mz.151-4.M4.bin but it doesn't seem to have ssh available.
vpdn enable vpdn-group 1 request-dialin protocol pppoe exit
My config looks something like this:
version 12.4 service timestamps debug datetime msec localtime show-timezone service timestamps log datetime msec localtime show-timezone service password-encryption service compress-config service sequence-numbers ! hostname myhostname ! boot-start-marker boot-end-marker ! logging buffered 51200 warnings enable secret 5 xxxxxxxx ! aaa new-model ! ! aaa authentication login local_auth local aaa authorization exec default local ! aaa session-id common ! resource policy ! mmi polling-interval 60 no mmi auto-configure no mmi pvc mmi snmp-timeout 180 ip subnet-zero ip cef ! ! ip domain name mydomainname.com ip ssh time-out 60 ip ssh authentication-retries 2 ip ssh version 2 vpdn enable ! ! interface FastEthernet0/0 description ADSL WAN connection no ip address no ip redirects no ip unreachables no ip proxy-arp no ip mroute-cache duplex auto speed auto pppoe enable no cdp enable ! interface FastEthernet0/1 ip address 10.1.1.5 255.255.255.252 no ip redirects no ip unreachables no ip proxy-arp ip nat inside ip virtual-reassembly no ip mroute-cache duplex auto speed auto no cdp enable ! ! interface Vlan1 no ip address ! interface Dialer1 description ADSL WAN Dialer ip address negotiated no ip unreachables ip mtu 1492 ip nat outside ip virtual-reassembly encapsulation ppp ip tcp adjust-mss 1452 no ip mroute-cache dialer pool 1 dialer-group 1 no cdp enable ppp authentication chap pap callin ppp chap hostname myname@myisp ppp chap password d xxxxxxxx ppp pap sent-username myname@myisp password d xxxxxxxx ppp ipcp route default ! ip classless ! no ip http server ip http access-class 23 ip http authentication local ip http secure-server ip http timeout-policy idle 60 life 86400 requests 10000 ip nat inside source list 10 interface Dialer1 overload ip nat inside source static 10.1.1.6 15.14.13.12 ! logging trap debugging logging facility local6 access-list 10 permit 10.1.0.0 0.0.255.255 access-list 23 permit 10.1.0.0 0.0.255.255 dialer-list 1 protocol ip permit no cdp run !
Solved! Go to Solution.
06-20-2012 11:56 PM
Hello Kim,
The VPDN configuration is not relevant to what you are trying to accomplish. Please remove all VPDN-related commands, i.e.:
no vpdn-group 1
no vpdn enable
What you are currently missing in the configuration you posted is a simple line on the FastEthernet0/0 interface:
pppoe-client dial-pool-number 1
Adding this line should successfully start the PPPoE client and tie its operation to the Dialer1 interface.
Also, please remove the ppp authentication chap pap callin line from your Di1 interface - it is again not relevant to your configuration. The authentification will still work successfully but this command is used to perform an authentication in the reversed direction during callbacks - clearly not your case here.
Best regards,
Peter
06-20-2012 11:56 PM
Hello Kim,
The VPDN configuration is not relevant to what you are trying to accomplish. Please remove all VPDN-related commands, i.e.:
no vpdn-group 1
no vpdn enable
What you are currently missing in the configuration you posted is a simple line on the FastEthernet0/0 interface:
pppoe-client dial-pool-number 1
Adding this line should successfully start the PPPoE client and tie its operation to the Dialer1 interface.
Also, please remove the ppp authentication chap pap callin line from your Di1 interface - it is again not relevant to your configuration. The authentification will still work successfully but this command is used to perform an authentication in the reversed direction during callbacks - clearly not your case here.
Best regards,
Peter
06-21-2012 07:08 PM
Many thanks, I'll give that a try.
06-26-2012 10:57 PM
Thanks, worked perfectly.
06-24-2020 03:48 AM
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide