cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2189
Views
0
Helpful
9
Replies

VIRL inter VLAN routing issue

hassan4917
Level 1
Level 1

Hi,

this is my very simple topology in VIRL:

IOSvL2 (running IP routing) <-----trunk with VLANs allowed + Native VLAN----> IOSvL2 (NO IP routing) <----> 2 hosts on different VLANs

The interfaces connecting the hosts are standard issue access ports with the relevant VLANs. The hosts are what i get with VIRL, i.e. ubuntu/coreOS.

I can ping from the ubuntu host to the default gateway which is the SVI on the IOSvL2 switch in the same vlan, and same in opposite direction

I can ping SVI in VLAN X source VLAN Y within the IOSvL2 switch.

What I can't do is ping the host from a different VLAN, i.e. ping Ubuntu host in vlan X from source VLAN Y. Same issue in opposite direction, i.e. host to another host in another VLAN (and also to SVI in another VLAN).

For troubleshooting, I replaced the Ubuntu host with an IOSv router and configured an IP on an interface, just in case the issue was with the Linux config but got the exact same issue.

The issue is pointing to IOSvL2 switch running IP routing. 

This is basic beginner CCNA lab and I really want to get this working so I can test some more advanced features before putting into business critical production network.

I found this thread with a very similar issue and tried the solution proposed there, and just like the fellow member this is also driving me mad. This really isn't a spectacular setup, am just trying to achieve inter-VLAN routing

https://community.cisco.com/t5/routing/virl-routing-issue/m-p/4064748#M332513

 

Is this some kind of bug with with the IOSvL2 image in VIRL, or have I just missed something really obvious? as I'm fresh out of ideas?

I have attached the running config of both the L2 and l3 switches 

 

Happy to provide more details/configs if required

 

 

1 Accepted Solution

Accepted Solutions

Hi @hassan4917 ,

You do not have a default gateway configured on either host. If you did, you would see something like this:

default via 10.0.151.254 dev ens2

you need to add the GW using the following command:

 

sudo ip route add default via 10.0.51.254

sudo ip route add default via 10.0.151.254

 

Regards,

Harold Ritter
Sr Technical Leader
CCIE 4168 (R&S, SP)
harold@cisco.com
México móvil: +52 1 55 8312 4915
Cisco México
Paseo de la Reforma 222
Piso 19
Cuauhtémoc, Juárez
Ciudad de México, 06600
México

View solution in original post

9 Replies 9

balaji.bandi
Hall of Fame
Hall of Fame

On the both the switches ? have you created the VLANs ?(especially Layer2 switch)

can you post below information :

show vlan

show ip routing

show ip arp

show spann brief

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

hi @balaji.bandi 

I have attached the output for both switches for these.

Thank you for the information, now tell me what VLAN end device not working to what VLAN

what is the source VLAN and destinatio vlan you try to reach.

Please confirm, from L3 switch are you able to ping end device ?

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

Hello
Just to confirm both hosts are attached to the same L2 switch , so did you manauly create the vlans on the both switchs and enable ip routing on the L3 switch?



conf t
vlan 2,32,40,51,151
exit

Please rate and mark as an accepted solution if you have found any of the information provided useful.
This then could assist others on these forums to find a valuable answer and broadens the community’s global network.

Kind Regards
Paul

hi @paul driver 

yes both hosts are attached to the same L2 switch and I did configure the VLANs manually.

the actual topology is bigger and am satisfied that the OSPF is working fine between all the router devices across the whole topology. 

However, I need to have communication between the simulated end host devices working as the next phase of the simulation is to run ACLs and route-maps - but can't due to this issue.

Hi @hassan4917 ,

Did you configure a default gateway on the two hosts pointing at 10.0.51.254 and 10.0.151.254 respectively?

Regards,

Harold Ritter
Sr Technical Leader
CCIE 4168 (R&S, SP)
harold@cisco.com
México móvil: +52 1 55 8312 4915
Cisco México
Paseo de la Reforma 222
Piso 19
Cuauhtémoc, Juárez
Ciudad de México, 06600
México

hi @Harold Ritter 

yes i have - please see attached

 

Hi @hassan4917 ,

You do not have a default gateway configured on either host. If you did, you would see something like this:

default via 10.0.151.254 dev ens2

you need to add the GW using the following command:

 

sudo ip route add default via 10.0.51.254

sudo ip route add default via 10.0.151.254

 

Regards,

Harold Ritter
Sr Technical Leader
CCIE 4168 (R&S, SP)
harold@cisco.com
México móvil: +52 1 55 8312 4915
Cisco México
Paseo de la Reforma 222
Piso 19
Cuauhtémoc, Juárez
Ciudad de México, 06600
México

I see... so I used the command

sudo ip route add 10.0.151.254 dev ens2

to set the DG. Just entered your command and that worked straight away.

slightly embarrassed but at least have learned something.

Thanks @Harold Ritter 

 

Review Cisco Networking for a $25 gift card