05-24-2019 03:34 PM
Hi there,
Thanks for reading.
I have a pair of high availability HSRP routers for which i've configured in-place replacement routers. I know that i can work on the router in Standby status without worrying about interrupting traffic but i'd like to manually change status on the Active router to Standby once I've replaced the current Standby.
Attached are the (I think) relevant show outputs.
What are the commands to do this?
Thanks!
Bob
05-24-2019 04:04 PM
05-24-2019 06:05 PM - edited 05-24-2019 06:08 PM
@Bob Greer hello,
add commands in bold to solve your problem
RT01 & RT02
RT01
interface GigabitEthernet0/0
description Internet
ip address aa.107.183.yy 255.255.255.224
ip nat outside
standby 1 ip aa.107.183.xx
standby 1 timers 1 10
standby 1 priority 200
standby 1 preempt
standby 1 name xvpn_ha
standby 1 track 1 decrement 150
crypto map xvpn redundancy xvpn_ha
end
!
interface GigabitEthernet0/1
description LAN
ip address 10.150.249.249 255.255.255.0
ip nat inside
standby 10 ip 10.150.249.250
standby 10 priority 200
standby 10 preempt
standby 10 track 2 decrement 150
|
Interface Grp Pri P State Active Standby Virtual IP
Gi0/0 1 200 P Active local aa.107.183.xx aa.107.183.yy
Gi0/1 10 200 P Active local 10.150.249.248 10.150.249.250
===============================================================
RT02
interface GigabitEthernet0/0
description INTERNET
ip address aa.107.183.xx 255.255.255.224
ip nat ouside
standby 1 ip aa.107.183.xx
standby 1 timers 1 10
standby 1 name xvpn_ha
standby 1 preempt
standby 1 track 1 decrement 150
crypto map xvpn redundancy xvpn_ha
end
interface GigabitEthernet0/1
description LAN
ip address 10.150.249.248 255.255.255.0
ip nat inside
standby 10 ip 10.150.249.250
standby 10 preempt
standby 10 track 2 decrement 150
end
P indicates configured to preempt.
|
Interface Grp Pri P State Active Standby Virtual IP
Gi0/0 1 100 Standby aa.107.183.yy local aa.107.183.xx
Gi0/1 10 100 Standby 10.150.249.249 local 10.150.249.250
if possible, share track 1 and 2 configuration and your default routes;
Regards,
05-25-2019 12:23 AM - edited 05-25-2019 12:24 AM
Hello Bob,
you have two different HSRP groups on two different interfaces.
In order to make RT02 active for both groups in order to perform a SW update on RT01 you need
int gi0/0
standby 1 priority 240
int gi0/1
standby 10 priority 240
After RT01 comes back you just need to remove the two commands above from RT02 to go back to previous configuration
the preempt command is necessary without it no HSRP active switchover can occur. And it is needed on both routers both interfaces for their respective HSRP groups 1 and 10.
Hope to help
Giuseppe
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide