cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
6530
Views
0
Helpful
18
Replies

Watch Dog Timeout constantly rebooting my C3845

Maciej Bylica
Level 1
Level 1

Hello,

I have purchased Cisco 3845 and have problems to boot it without problems.

To be more precisely i am getting "Watch Dog Timeout Reset" and box is constantly rebooting itself.

------ log 1 --------------------------------------------

System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 2006 by cisco Systems, Inc.

System Bootstrap, Version 12.4(13r)T11, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 2008 by cisco Systems, Inc.

Total memory size = 512 MB - DIMM0 = 512 MB, DIMM1 = 0 MB

c3845 platform with 524288 Kbytes of main memory

Main memory is configured to 72/0(dimm 0/1) bit mode with ECC enabled

Upgrade ROMMON initialized

program load complete, entry point: 0x8000f000, size: 0xcb40

program load complete, entry point: 0x8000f000, size: 0xcb40

program load complete, entry point: 0x80010000, size: 0x2212d64

Self decompressing the image : ################################################################################################################################################################################################################################################################################################################################################################################################## [OK]

Smart Init is enabled

smart init is sizing iomem

  ID            MEMORY_REQ                 TYPE

00042C          0X010D78F3 C3845 motherboard

                0X00280000 OIR memory

                0X00288860 Onboard PVDM2 SIMM

                0X000021B8 Onboard USB

                0X00660670 public buffer pools

                0X0078F000 public particle pools

TOTAL:          0X023D197B

If any of the above Memory Requirements are

"UNKNOWN", you may be using an unsupported

configuration or there is a software problem and

system operation may be compromised.

Rounded IOMEM up to: 36Mb.

Using 7 percent iomem. [36Mb/512Mb]

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.

           170 West Tasman Drive

           San Jose, California 95134-1706

Cisco IOS Software, 3800 Software (C3845-SPSERVICESK9-M), Version 12.4(9)T7, RELEASE SOFTWARE (fc3)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2008 by Cisco Systems, Inc.

Compiled Thu 10-Jan-08 18:36 by prod_rel_team

Image text-base: 0x60011084, data-base: 0x62CE4190

System Bootstrap, Version 12.4(13r)T11, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 2008 by cisco Systems, Inc.

*** Watch Dog Timeout Reset ***

ra = 0x603cd1f0, EPC = 0x603cd1f0

*** BCM 1125 went through a full reset. HT/PCI fabric reset. ***

------ log 1 --------------------------------------------

Here are few steps that i have aleady done to solve this:

1) use different CF with the same result

2) use few IOS  c3845-ipbase-mz.124-18.bin, c3845-ipvoicek9-mz.124-17.bin,

c3845-ipvoicek9-mz.124-22.T.bin, c3845-spservicesk9-mz.124-13c.bin with the same result

3) tried to boot IOS from rommon mode with exactly the same after-effect

4) checked if cookie is okay. Unfortunately i cannot say that the whole cookie is okay, but beginning octets are not FF's.

cookie:

04 ff c1 8b 46 4f 43 31 33 32 38 36 32 4d 52 40

04 2c 41 01 04 c0 46 03 20 00 5c 40 07 42 43 30

88 00 01 8e fa 02 05 03 00 81 00 00 00 00 04 00

09 69 c6 8a 49 50 4d 4e 58 30 30 44 52 41 cb 8c

43 49 53 43 4f 33 38 34 35 2d 4d 42 89 56 30 37

20 d9 02 40 c1 c3 06 00 26 0b d3 90 10 43 00 30

82 49 22 5f 0a 83 01 32 8f 5b c2 8b 46 54 58 31

33 33 31 41 4a 42 42 ff ff ff ff ff ff ff ff ff

Could you please tell me where to look for "Chassis MAC Address" so i can compare? - first octets?

5) tried to upload ios from rommon mode without success. See logs below:

------ log 2 --------------------------------------------

rommon 3 > IP_ADDRESS=192.168.1.5

rommon 4 > IP_SUBNET_MASK=255.255.255.0

rommon 5 > DEFAULT_GATEWAY=192.168.1.1

rommon 6 > TFTP_SERVER=192.168.1.10

rommon 7 > TFTP_FILE=c3825-spservicesk9-mz.124-24.T.bin

rommon 8 > tftpdnld

          IP_ADDRESS: 192.168.1.5

      IP_SUBNET_MASK: 255.255.255.0

     DEFAULT_GATEWAY: 192.168.1.1

         TFTP_SERVER: 192.168.1.10

           TFTP_FILE: c3825-spservicesk9-mz.124-24.T.bin

             GE_PORT: Ge0/0

     TFTP_MEDIA_TYPE: Copper

       GE_SPEED_MODE: Auto

Invoke this command for disaster recovery only.

WARNING: all existing data in all partitions on flash: will be lost!

Do you wish to continue? y/n:  [n]:  y

Mac Address: 0026.0bd3.9010

Receiving c3825-spservicesk9-mz.124-24.T.bin from 192.168.1.10 !!!!!!!!!!!!!!!!!!!!!!!!

....................

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

File reception completed.

TFTP flash copy: Invalid file header, copy terminated.

         Reason: Wrong target platform OR corrupt file.

------ log 2 --------------------------------------------

6) Removing PVDMs did not change anything

I have no idea how to solve this.

Could anyone give me advice.

Regards,

Maciej

2 Accepted Solutions

Accepted Solutions

Broken faulty router, that Cisco will replace if under support contract.

View solution in original post

if you are complaining about your 3845 rebooting all the time, why are you trying to load a 3825 ios?  Get the correct ios and try again.

It's got nothing to do with the IOS.  If you look at the bootup process after the router passes the bootstrap the router crashes.  It's a hardware fault.

View solution in original post

18 Replies 18

Reza Sharifi
Hall of Fame
Hall of Fame

Hi,

If this is new router, most likely you have a hardware problem.  Open a ticket with TAC and RMA the router

Here is more info regarding the error message:

http://www.cisco.com/en/US/products/sw/iosswrel/ps1835/products_tech_note09186a00800f67db.shtml

HTH

Thanks Reza for prompt answer.

This is second hand router

Btw: your link does not work.

If it is second hand then I assume you don't have a service contract to replace it.  Since the router keep rebooting, try using the following link to see if you can break in to the router and load a different IOS.

http://www.cisco.com/en/US/products/hw/routers/ps274/products_password_recovery09186a0080094774.shtml

HTH

I was trying to load different IOS several times but still Cisco was rebooting itself.

As i stated previously Cisco was originaly shipped with c3845-spservicesk9-mz.124-13c.bin, but i was trying c3845-ipbase-mz.124-18.bin, c3845-ipvoicek9-mz.124-17.bin, c3845-ipvoicek9-mz.124-22.T.bin as well

Of course that was only possible from Rommon mode (from few CF's cards or tftp), because watchdog prevents from giving me prompt.

Regarding "Troubleshooting Watchdog Timeouts" page it is probably software watchdog timeout (i pasted all the output).

If you could get to Rommon mode, you could also use Xmodem to try to load a new IOS.

http://www.cisco.com/en/US/products/hw/routers/ps259/products_tech_note09186a008015bfac.shtml

HTH

I was trying to upload IOS to Cisco with confreg 0x3922 but at the end got error that the file cannot be opened.

Ready to receive file c3845-ipbase-mz.124-18.bin ...

program load complete, entry point: 0x8000f000, size: 0xcb40

Format: All system sectors written. OK...

Format: Operation completed successfully.

Format of flash: complete

program load complete, entry point: 0x8000f000, size: 0xcb40

open(): Open Error = -13

create a file failed...err code = -1

rommon 2 >

I need to check another CF card tomorrow and give us an update here.

There is no need to use xmodem with modern routers.

You can do tftpdnld -r to load and boot the image without writing to flash.

However from previous posts I suspect you have faulty hardware.

Is there any way to find what exactly is out of order?

Dont' you think that cookie might be corrupted?

Broken faulty router, that Cisco will replace if under support contract.

Paulo, unfortunately that Cisco is not under any support contract

Don't you think that cookie might be responsible for such Cisco behaviour?

04 ff c1 8b 46 4f 43 31 33 32 38 36 32 4d 52 40

04 2c 41 01 04 c0 46 03 20 00 5c 40 07 42 43 30

88 00 01 8e fa 02 05 03 00 81 00 00 00 00 04 00

09 69 c6 8a 49 50 4d 4e 58 30 30 44 52 41 cb 8c

43 49 53 43 4f 33 38 34 35 2d 4d 42 89 56 30 37

20 d9 02 40 c1 c3 06 00 26 0b d3 90 10 43 00 30

82 49 22 5f 0a 83 01 32 8f 5b c2 8b 46 54 58 31

33 33 31 41 4a 42 42 ff ff ff ff ff ff ff ff ff

No.

You can buy a support contract at any time.

lsharrah
Level 1
Level 1

if you are complaining about your 3845 rebooting all the time, why are you trying to load a 3825 ios?  Get the correct ios and try again.

if you are complaining about your 3845 rebooting all the time, why are you trying to load a 3825 ios?  Get the correct ios and try again.

It's got nothing to do with the IOS.  If you look at the bootup process after the router passes the bootstrap the router crashes.  It's a hardware fault.

Review Cisco Networking for a $25 gift card