As far as I know, looking at SD-WAN's DNA licensing system, if you use it without a license, there is a bandwidth limit of 250MB regardless of equipment performance.Additionally, I understand that if you allocate DNA License Tier 0 or Tier 1, you can...
Forum Posts
Hi, I configured OSPF on my service side in order to have reachability from the cEdge to my end-host in the LAN. This reachability is working well. However the LAN subnet is not being learned by OMP and thus not being advertised to other sites. So, ...
i am trying to upgrade my vedge viptela image using the following command and i am getting the following error: vedge# request software install reboot viptela-20.4.1.2-mips64.tar.gzls: cannot access 'viptela-20.4.1.2-mips64.tar.gz': No such file or d...
Resolved! Pinging devices on same VLAN MX84
I have a MX84, and today, I am not able to ping a device on LAN port 3 to Lan port 6 in the native vlan1. Bother devices are in the same network with the same DGwy and same netmask. I can ping from the dashborad to the internet, 8.8.8.8, and can ping...
Hello Guys, Am trying to implement Feature Template but getting following error, i have same feature templates for both vpn0 and vpn512 with interface id difference. ####################################################################### 19-Jan-202...
Hello!I have problem with transfer between VLANs.I have Cisco Meraki MX64 and switch. Transfer between VLANs (when I move files like .exe) is 30 - 32 MB/s is very slow ...When I move these same files in this same VLAN I have transfer about 600 - 700 ...
Hello TeamI want to allow only single system ip / bfd session and block all other. How to configure this via cli mode in sdwan
Hi, sorry very specific one here. I've understand (from documentation) that under normal circumstances it's not expected or allowed to have SNMP RW enabled on a IOS XE device that's attached to vManage/Cat SD-WAN manager - I appreciate you want the c...
Hello EveryoneWe are currently having 1 * Carrier in the VPN 0 (G0/0/0) whilst the Clients are in VPN 20. We want to connect Private SIP Trunks to the network and requesting for your advise if the approach below is fine.1. Connect the Private SIP Tru...
I wanted to be able to better understand how the SD-WAN topology works on a sandbox environment. However, I have not found any documents that clearly indicate this topology. Can someone please give me an overview?Because I can't access the device, I ...
Hi Community, I am trying to move my SD-WAN to use Configuration-Groups.most of the stuff I can build with configuration-groups as I had it befor with Device and feature templates.Burt there is one missing link In the feature-template of a WAN interf...
I am trying to upgrade viptela image from cli because it's not managed by vmanage however i am getting the following error: vedge# request software install viptela-20.4.1.2-mips64.tar.gz rebootERROR: install: Kernel image not found Note that the MD5s...
When deploying SD-WAN configuration using new Configuration Group method. How do you make certain parts optional when deploying configuration. For example a Static Route / BGP routing to a specific site out of a group of WAN routers on the service s...
Hi I've read the SD-WAN Cisco Press book and recently completed the Cisco U SD-WAN Deployment Course which was great by the way. I get the idea SD-WAN is supposed to be flexible and customizable etc.. and everything from templates section are buildi...
Hi GuysI am troubleshooting NTP connectivity and a sync failure using TCPDUMP. When I run the tcpdump interface X/X options "dst ip X.X.X.X" or tcpdump vpn X options "dst ip X.X.X.X", I don't see any traffic being sent out to the NTP Server. The TCPD...
