In my environment we have multiple cEdge devices, 1 vManage, 2 vBond and 2 vSmart.Due to some reasons one of the cEdge devices lost connectivity to vMange. Not sure of the exact reason.But would like to understand, will there be any impact due to thi...
Hello Guys,Good Day !!Need your help and guidance on cli commands to configure the NAT for the Internet Link on cisco cEdge for the direct L3 TLOC extension (Private IP address) between the 2 cEdges.In vEdge we can simply config NAT enable under the ...
Is it possible to mark a variable as optional in sd-wan cli template?Can we use variables in a local data policy? I want to apply an ACL to internet facing interface that only permits traffic to the internet facing IP only. Policy will be applied to ...
Hi Guys, Can somebody help to identify what might be the problem here? I'm trying to redistribute NAT DIA into BGP but it's not working. Please see screenshot below. It only worked as expected after I put network 0.0.0.0 statement on bgp.
Hello, team. Good day. We are planning to upgrade below platforms to 20.9.x. Is there any upgrade path ? - vEdge 5000 20.3.3 - vEdge 2000 20.6.3 - ISR1100-6G (Viptela OS) 20.6.3 Thanks.
hello, So in my lab i just have 3 CEDGE (CRSv) and i want to connect them to the controllers the only consideration is that the link are MPLS ONLY or in this case i put gi1 color private1 and gi2 color private2 on the SDWAN-DC device and i created r...
Hello , We would run dual stack (IPv4 & IPv6) at service side, and also we would run dual stack (IPv4 & IPv6) on the transport internet interface(underlay), on SD-WAN router. Is it possible to enable IPv4DIA (NAT44) and IPv6 DIA (NAT66) via the same...
The route learned by OSPF from the LAN is re-distributed to OMP for publicity to other sites.I do not want to advertise the specific routes from OSPF. What kind of 'configuration' should we use ?I want to control this in the SD-WAN Router side, not t...
In my environment I have 2 vSmart controllers. (vSmart-1, vSmart-2)In cEdge-1, the OMP peer is established only with vSmart-1. No details about peering with vSmart-2.in cEdge-2. the OMP peer is established with vSmart-1, for vSmart-2, the status is i...
We have a Cisco hosted SD-WAN fabric in a shared environment meaning we are a tenant that uses shared control components. There is a c8000v hosted in AWS that we onboarded and has active control connections to vBond and vManage. For some reason I'm n...
In scenarios where there are 2 vBonds, how the redundancy works ?In normal scenarios, are both the vBonds are active - active or active - standby.How the redundancy works in case of failure of 1 vBond ?
For the below commad in cEge, in normal scenario it should show only vSmart and vMange.Plse claify if myunderstandng is correct ? Does vBond will be visible in the output ? show sdwan control connections
If a cEdge has 2 internet connections & there are 2 vSmart & in this scenario how many control connections will be establisehed.Will it be 4 or 2 ? 4 means each internet link IP wll form connection with both the vSmart, so there should be 4.Is my und...
I have 3 C8KV devices in my LAB topologyTwo of them have been able to form control connections with all controllers.One can form control connections with vmanage and vbond but not vsmart. SITE33#show sdwan control connectionsvbond dtls vmanage dtls S...
Sign up for the SD-WAN Interconnects EFT today! We’re thrilled to announce that SD-WAN Interconnects is now available for private beta & early field trial (EFT). Customers using both Meraki and Catalyst SD-WAN can now enable transit between VPN fabr...
