SD-WAN and Cloud Networking

In my topology, I have my vmanage connected to a cisco router, where the router acts like a VPN server.There is a windows machine too which is able to receive the updates from the NTP server and also accept its. However, my vmanage, receives the upda...

We are deploying an SD-WAN environment in a HUB-Spoke configuration, where tunnels from the Site to the HUB and to other Sites are up. When a tunnel between Sites goes down, we want to be notified through some means. Do you know if there's any way to...

How Active vBond and vsmart communicate with standby vBond and vsmart in Cisco SDWAN veptila

In our critical sites we typically have 1 internet circuit and a AT&T AVPN (MPLS) private circuit used more for failover. What type of circuit would be a good replacement for MPLS and still have good resiliency in our sites?  MPLS is expensive.  

Dear Cisco Community , i want to downgrade my Vmanage from 19.2.3 to 18.4.5 , initially i was having 18.4.5 version but i upgraded it to 19.2.3 and now when i try to downgrade this to again 18.4.5 my vmanage reboots and again come with 19.2.3 .can an...

GuysDoes anyone know a document that can help dual stacking my controller complex (vManage/ vBond/ vSmart)?1-My environment is fully up and functioning with IPV42- I have dual stacked my entire environment, there is IPV6 underlay end to end reachabil...

Hello all, I am in sales handling SD-WAN solutions.Therefore, I am leaving an inquiry because I have some questions regarding SD-WAN. I understand that when configuring SD-WAN, it is implemented by configuring the fabric on the controller. However, i...

Hi all Im working with viptela version 18.4.1 every time I try to add the vBbond to the vMange I get this error java.net.SocketTimeoutException: connect timed out Thanks. 

This is regarding upgrading Cisco SD-WAN for minor releases.I would like to know what are the steps , sequences, recommendations that needs to be followed when upgrading the vManage, vBond/vSmart & the cEdges.Is it always required to upgrade all the ...

I would like to upgrade our SDWAN environment to code that supports XE SD-WAN code.  We have Vedge 2000 head ends and a mixture of Vedge 1000, 100-4G and 1100-6G boxes at 140 sites.Can I upgrade the Vedge 2000's to code that supports XE SD-WAN, or do...

By default the BW is set to 100K on the tunnel interface and the monitoring tools are complaining about this. is there any way to override this? Tunnel2 is up, line protocol is upHardware is TunnelInterface is unnumbered. Using address of GigabitEthe...

Good Day,I'm upgrading my C1100 devices from 16.2.5 to 17.06.05 via vManage. After doing the upgrade step, onto the activation, some of the routers are showing just "17.06.05" and these are failing with error "Cannot copy ios and sdwan cli configurat...

I want to establish a centralized policy in SD-WAN to route traffic to a particular destination FQDN. I understand that in vManage, there are Custom Applications that allow me to define specific FQDNs or applications. However, when attempting to crea...

We are running vManage v20,3,4 on EVE.I've created the ACL via Localized Policy, and I have already applied an egress ACL on cEdge's interface, and then it's work.I didn't see any ACL log on monitor pages.Do I miss something config?below is my config...

Hi team, I need to understand when we need adding Root CA to vBOND controller in Cisco PNP. Suppose, I use on-premise controllers and enterprise CA for controller authorization. In addition, I want vedge authorization to be done automatically (vmanag...