I want to establish a centralized policy in SD-WAN to route traffic to a particular destination FQDN. I understand that in vManage, there are Custom Applications that allow me to define specific FQDNs or applications. However, when attempting to crea...
Forum Posts
We are running vManage v20,3,4 on EVE.I've created the ACL via Localized Policy, and I have already applied an egress ACL on cEdge's interface, and then it's work.I didn't see any ACL log on monitor pages.Do I miss something config?below is my config...
Hi team, I need to understand when we need adding Root CA to vBOND controller in Cisco PNP. Suppose, I use on-premise controllers and enterprise CA for controller authorization. In addition, I want vedge authorization to be done automatically (vmanag...
Hello, For testing purpose, i have created a overlay tunnel between site-5 to site-6. Though, i am getting a service vpn 10 route via OMP but unable to ping those prefix from site-6 Vedge devcie. Can i get a solution or suggestion if i missed somethi...
Hello, I would like to ask if it is possible to configure 802.1Q on a portchannel. I attached an image of the topology. I would like to use the Po1.100 interface as a service VPN and the Po1.200, Po1.300 interface as a transport VPN. The device is an...
Resolved! C8000v Device template issues
Hello, I am trying push an SD-WAN device template to a C8000v device. I keep getting the same error mentioned below. I successfully sent device templates to several vEdge devices on my network. Its just a basic config with VPN 0 and the transport int...
Hi community, are there any plans to povide NETCONF northbound API for the vManage? For now only custom rest api is available. Since vManage tech stack is based on NSO/confd it would be very nice to have NETCONF API for CFS side of vManage service to...
Hello My vedge routers all have control connections to vbond and in Up state (because of only one vsmart controller) over public internet transport. control connections from vedge routers to vbond state show connect (show control connections) and bla...
Resolved! C8200 max uplinks
Hello,Checking C8200-1N-4T and C8300-1N-4T as a candidate to substitute the current silver peak solution I have in place. I can’t find information in the documentation about what is the maximum number of uplinks (RG45) that can be connected to the ro...
We have two sites, the Hub site and the Spoke site, both of which use TLOC-EXT. We found that the Spoke site Internet interface address (59.39.38.106 and 120.86.8.30) cannot be pinged from the Hub site., but the BFD sessions are normal The Internet i...
On the SDWAN routers that are in controller mode, I need to remove HMAC-SHA1 from the list of options for SSH to connect. Is there a template that would be used to modify SSH, like a CLI template. I am looking to push the equivalent commands down to ...
Hi all,I recently came across a presentation from Cisco Live 2020 on the Cisco Live OnDemand website (BRKRST-2377) : https://www.ciscolive.com/c/dam/r/ciscolive/emea/docs/2020/pdf/BRKRST-2377.pdfWhile reviewing the material, I noticed a point of inte...
Hello Team, Being new to SDWAN solution, I have deploy Viptela components with 3xvManage, 3xvSmart , 2xvBond , 4xvEdge and 4xCSRv/ISRv on EVE-NG . I want to do configuration backup of all components and I have some questions as mentioned below :- 1....
Hi All, I have a client looking to deploy SD WAN remote access. They currently use Palo Alto firewalls, and have Global Protect as their VPN client. Naturally, all of the cisco documentation only mentions any connect. There is a small mention of 3rd ...
Hello Team, I am trying to deploy SDWAN components on EVE-NG , but unfortunately am not able to see System-IP/IP information as shown in snapshot. The vManager cluster is working fine and i have installed certificate using Enterpsise CA and it shows...
