Firepower 2100 series platform can run either FTD or ASA software.
When Firepower 2100 series platform running ASA, has two software, FXOS and ASA. Both have its own management IP address and share same physical Interface Management 1/1.
Both ASA and FXOS has its own authentication, same with SNMP, Syslog and tech-support logs.
Toggle between FXOS & ASA prompt:
From FXOS prompt, you can use "connect asa" to go to ASA prompt, "exit" to come back to FXOS.
From ASA prompt, you can use "connectfxos" to go to FXOS prompt, "exit" to come back to ASA.
When using Console, you'll login to fxos prmpt.
ssh/telnet to ASA Management IP to access ASA.
ssh to fxos management IP to access FXOS.
ASA & FXOS Management:
In order to manage ASA, you have ASDM or CLI (SSH, Telnet). To manager FXOS, we have CLI and FCM-Firepower Chassis Manager - Browser base GUI tool.
FXOS useful configurations:-
The Default IP address for FXOS IP address for FP2100 running ASA is 192.168.45.45.
Verify & Configuring Management IP address for FXOS:-
To Verify FXOS IP address
firepower-2110# scope fabric-interconnect a
firepower-2110 /fabric-interconnect #show detail
Product Name: Cisco FPR 2110
Vendor: Cisco Systems, Inc.
Serial (SN): JMX202820M4
OOB IP Addr: 192.168.45.45
OOB Netmask: 255.255.255.0
OOB Gateway: 192.168.45.1
OOB Gateway Use DataPort: No
OOB Boot Proto: Static
OOB IPv6 Address: ::
OOB IPv6 Gateway: ::
OOB IPv6 Gateway Use DataPort: No
IPv6 Boot Proto: Static
DHCPD Admin State: DHCP Server Enabled
Changing FXOS management IP address:
firepower# scope fabric-interconnect a
firepower /fabric-interconnect # set out-of-band static ip 10.106.143.40 netmask 255.255.255.0 gw 10.106.143.1
firepower /fabric-interconnect* #commit-buffer (Commit buffer to save config)
some time you may get below error:
" Error: Update failed: [Management ipv4 address (IP 10.106.143.40 / net mask 255.255.255.0 ) is not in the same network of current DHCP server IP range 192.168.45.5 - 192.168.45.10. Either disable DHCP server first or config with a different ipv4 address.] "
If you get above error, you need to either disable DHCP or change DHCP range in the same subnet as new Management IP address.
Disabling DHCP Server:
firepower# scope system
firepower /system* #scope services
firepower /system* # disable dhcp-server
firepower /system* # enable dhcp-server 10.106.143.10 10.106.143.20 (To enable DHCP server on FXOS)
Configuring NTP ortimezone on ASA running on FP2100 is restricted. Clock,timezone,ntp need to be configured on FXOS, which will besync to ASA.
firepower# scope system
firepower/system* #scope services
firepower/system/services *# set clockoct6 2017 17 12 00
I tested using both Cisco ISE 2.4 (patch 9) and Cisco ISE 2.6 (patch 1). I have a user who successfully authenticated via RADIUS against ISE. Under ISE, Operations > Live Logs (and Live sessions), I see the user authenticated. After the accounting requ...
Hello,I would like to download ESA software for C695. But I cannot find any versions for this model.https://software.cisco.com/download/home/282509130Does anyone know how to find it and download it? Thank you!SH SHAO
Hello everyone, So I have a Cisco Firepower 2110 firewall with ASA version 9.8.2 and I'm using ASDM 7.8(2) to configure it. I have a strange dilemma that when I try to configure my interfaces is does not let me alter the ports media type from rj45 to...
Hello, We have a server on our internal network that we are currently using port forwarding to allow accessibility from the outside and I am considering placing it in a DMZ to limit potential attack surface. The problem is that clients on the inside ...
I have an ISP in Australia that requires VLAN 100 to connect to the Internet. This is pure data. It is Australia's NBN system. They have handed us a .252 Public IP to use on our Firewall with a default route to the upstream router they are using for...