Mobile endpoints utilizing random MAC address is nothing new. But the way it is utilized has changed since it was first introduced. In the beginning, the randomization of MAC was used to probe for known wireless networks by the devices. By randomizing the MAC address used in the probe request frame, devices were able to hide real MAC address thus providing some level of privacy. Fast forward few years, now devices started using random MAC addresses for the association to the wireless networks. This causes issue on the network elements which relies on MAC addresses to uniquely identify the endpoint or the user behind it. The implementations of MAC randomization are different depending on the vendor but here are few examples of the behavior:
Can setup randomization per network profile (SSID)
Randomization is enabled by default out-of-the-box
Once random MAC is used for a given network profile, device will keep using the same random MAC even after user deletes the network profile and recreates the profile
Randomization enabled upon update to iOS 14 from previous versions of iOS for existing SSIDs
Although this document is focused on ISE, it should be noted that the impact doesn’t stop with ISE. As MAC address as a unique identifier is hard-coded into products and solutions throughout Cisco and 3rd party, which includes MDM/EMM, wireless performance monitoring, and device profiling systems. ISE or wireless authentication system is in a unique position in the network to control the use of random MAC address for the rest of the network. The good news is that generation of random MAC follows rules set by IEEE. As noted in the diagram below, locally significant address 2’s bit of first byte is set to one. Any MAC address that has locally significant bit set as one and is also a unicast address can be considered a random MAC address.
So based on the rule, all of the numbers below would qualify as a random MAC address. For a simple rule, any MAC address’ first octet that ends 2,6,A,E would be a random MAC address.
With this, ISE policy rule can be created using a regular expression match against the RADIUS Calling-Station-ID attribute within the RADIUS Access-Request which includes the client MAC on virtually all Cisco devices: ^.[26AEae].*
Now that ISE can detect the random MAC, here are few options to consider:
1. Deny Access
User will not be able to connect to the wireless network
Bad experience as there could be many other reasons that user cannot connect to the network
2. Deny Access + Instructions
User will be able to connect, but will be redirected to a help page instructing user to disable random MAC feature for this network
Best option, if you do not want random MAC to enter the network.
3. Permit Access + Short session timeout
User will be able to connect, but after the device goes to sleep and awakes, user will be asked to login again
4. Permit Access + Short purge cycle
User will be able to connect, but user will be asked to login after X # of days
5. Permit Access + Consent
User will be prompted but can bypass and gain same level of access as unique MAC
6. Permit Access
User will be able to connect and there are no difference between random MAC and unique MAC
Note: Option 3-6 can be augmented with additional permission to restrict bandwidth, ACL, VLAN, etc. if needed.
Hi, Using an FMC. I turned on SNMP alerts for Intrusion Impact Alerts. Traps came through, but it's not showing all of the relevant OIDs that are possible given the Enterprise number. How can I enrich the SNMP traps coming from the FMC to show more o...
Hello,I have a pair of FTD 2130 configured as HA.I use FDM to manage these FWs.Every time I want to run "https" on its IP-mgmt address, it came out as http (not secured).Anyway I can configure the FTD without issue. But I feel uncomfortable why http...
Good evening to you allone question for you i don't know how to respond.. i have a cisco ASA (don't know more than this at the moment ) as per the picture attachedi would like to understand if possible to upgrade this ASA from IKEv1 to IKEv2 and if y...
In Context visibility for endpoints, there is a hardware tab. From the fields looks like an active program on Win or Mac endpoints that is collecting CPU status, BIOS data, etc every 5 mins.
Description says this date comes from ISE posture agent on...
Solo quiero saber si existe una manera de iniciar automáticamente un escaneo de cualquier dispositivo de almacenamiento cuando se conecta.En mi trabajo me exigen que realicemos automáticamente un análisis de amenazas / virus siempre que se conecte un disp...