The Portuguese version of this Article can be found at: ISE - Localized Installation (versão Português) .
 |
For an offline or printed copy of this document, simply choose ⋮ Options > Printer Friendly Page. You may then Print > Print to PDF or Copy & Paste to any other document format you like. |
Introduction
A new feature was created in Cisco ISE 3.2 Patch 5 to reduce the Time of Reinstalling Cisco ISE (saving at least 40 min), it is called Localized ISE Installation.
Note 1: this feature is also available from ISE 3.1 P9, ISE 3.3 P2 and ISE 3.4 !!!
Note 2: you can use this option to reinstall the Current or Higher Version of Cisco ISE !!!
Localized ISE Installation
How does it work ?
Create a Repository and copy the Cisco ISE ISO to the ISE Node disk (Cisco ISE 3.4 example) :
ise/admin# configure terminal
ise/admin(config)# repository <Repository Name>
ise/admin(config-repository-ISO)# url ftp: //<Server IP Addr>/
ise/admin(config-repository-ISO)# user <username> password plain <password>
ise/admin# copy repository <Repository Name> file ise-3.4.0.608a.SPA.x86_64.iso disk://
|
Cisco ISE ISOs:
|
Execute the command:
ise/admin# application configure ise
Selection configuration option
...
[25]Localized ISE Install
...
[0]Exit
25
ISO files present in the disk are:
[1] ise-3.4.0.608a.SPA.x86_64.iso
Choose the ISO you want to install: 1
Computing MD5 hash value of the selected ISO...
File selected: ise-3.4.0.608a.SPA.x86_64.iso (MD5: ac4f8bf234fd1b29ca0453ccd53102a7)
Warning: Verify the MD5 checksum of the ISO before you proceed.
Proceed with Installation? [y/n] y
Copying ISO contents to installer directories. The copy may take around 5 minutes.
% Notice: The appliance will reboot to install the chosen Cisco ISE release now.
Once the Installation is complete, simply follow the configuration via Setup:
**********************************************
Please type ‘setup’ to configure the appliance
**********************************************
localhost login: setup
|
Depending on the Cisco ISE version, the Localized ISE Install option is located in different positions:
|
Troubleshooting
If the ISO file is not copied, the following error will occur:
ise/admin# application configure ise
Selection configuration option
...
[25]Localized ISE Install
...
[0]Exit
25
Error: No ISO files found on the disk.
Upload the ISO file that you want to install into the disk. Then, select the "Localized ISE install" option.
If the copied ISO file is of an Earlier Version, the following error will occur:
ise/admin# application configure ise
Selection configuration option
...
[25]Localized ISE Install
...
[0]Exit
25
ISO files present in the disk are:
[1] ise-3.2.0.542a.SPA.x86_64.iso
Choose the ISO you want to install: 1
Computing MD5 hash value of the selected ISO...
File selected: ise-3.2.0.542a.SPA.x86_64.iso (MD5: 2e609b6cbeaa5c360d0a09a2a5d3c564)
Warning: Verify the MD5 checksum of the ISO before you proceed.
Proceed with Installation? [y/n] y
Error: You cannot install an earlier version of Cisco ISE (3.2.0). The minimum supported version for installation is 3.4.0
References
Configure Localized ISE Installation
Localized ISE Installation - CLI
ISE - Localized Installation (versão Português) - Video
