cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements

Ask the Expert- SD-WAN

1159
Views
0
Helpful
0
Replies
Highlighted
Beginner

Non-existent Port switch on Cisco Prime's alert (v3.1.0)

Hi all,

I have an alert in Cisco Prime about a "PD Removed", when I remove a PoE Cisco Phone un other interface, and mention a non-existent port on a switch that I'm administrating. This is the alert:

Critical SW-TEST May 7, 2019 9:23:22 AM PET Interface Gi1/0/42: PD removed - Device Name: SW-TEST - Reporting Address: -

 The switch just has 48 FastEthernet ports plus 4 GigabitEthernet ports (1to4).

Switch   Ports     Model            SW Version     SW Image
------ ----- ----- ---------- ----------
* 1 52 WS-C2960-48PST-S 15.0(2)SE11 C2960-LANLITEK9-M

And the ports are:

Port Name    Status      Vlan   Duplex Speed     Type
Fa0/1 connected 26 a-full a-100 10/100BaseTX
Fa0/2 notconnect 26 auto auto 10/100BaseTX
Fa0/3 connected 26 a-full a-100 10/100BaseTX
Fa0/4 notconnect 26 auto auto 10/100BaseTX
Fa0/5 notconnect 26 auto auto 10/100BaseTX
Fa0/6 connected 26 a-full a-100 10/100BaseTX
Fa0/7 notconnect 26 auto auto 10/100BaseTX
Fa0/8 notconnect 26 auto auto 10/100BaseTX
Fa0/9 notconnect 26 auto auto 10/100BaseTX
Fa0/10 notconnect 26 auto auto 10/100BaseTX
Fa0/11 notconnect 26 auto auto 10/100BaseTX
Fa0/12 notconnect 26 auto auto 10/100BaseTX
Fa0/13 notconnect 10 auto auto 10/100BaseTX
Fa0/14 notconnect 26 auto auto 10/100BaseTX
Fa0/15 notconnect 26 auto auto 10/100BaseTX
Fa0/16 notconnect 26 auto auto 10/100BaseTX
Fa0/17 notconnect 26 auto auto 10/100BaseTX
Fa0/18 notconnect 26 auto auto 10/100BaseTX
Fa0/19 notconnect 26 auto auto 10/100BaseTX
Fa0/20 notconnect 26 auto auto 10/100BaseTX
Fa0/21 notconnect 26 auto auto 10/100BaseTX
Fa0/22 notconnect 26 auto auto 10/100BaseTX
Fa0/23 notconnect 26 auto auto 10/100BaseTX
Fa0/24 notconnect 26 auto auto 10/100BaseTX
Fa0/25 notconnect 26 auto auto 10/100BaseTX
Fa0/26 notconnect 26 auto auto 10/100BaseTX
Fa0/27 notconnect 26 auto auto 10/100BaseTX
Fa0/28 notconnect 26 auto auto 10/100BaseTX
Fa0/29 notconnect 26 auto auto 10/100BaseTX
Fa0/30 notconnect 26 auto auto 10/100BaseTX
Fa0/31 notconnect 26 auto auto 10/100BaseTX
Fa0/32 notconnect 26 auto auto 10/100BaseTX
Fa0/33 notconnect 26 auto auto 10/100BaseTX
Fa0/34 notconnect 26 auto auto 10/100BaseTX
Fa0/35 notconnect 26 auto auto 10/100BaseTX
Fa0/36 notconnect 26 auto auto 10/100BaseTX
Fa0/37 notconnect 26 auto auto 10/100BaseTX
Fa0/38 notconnect 26 auto auto 10/100BaseTX
Fa0/39 notconnect 26 auto auto 10/100BaseTX
Fa0/40 notconnect 26 auto auto 10/100BaseTX
Fa0/41 notconnect 26 auto auto 10/100BaseTX
Fa0/42 notconnect 26 auto auto 10/100BaseTX
Fa0/43 notconnect 26 auto auto 10/100BaseTX
Fa0/44 notconnect 26 auto auto 10/100BaseTX
Fa0/45 notconnect 26 auto auto 10/100BaseTX
Fa0/46 notconnect 26 auto auto 10/100BaseTX
Fa0/47 connected trunk a-full a-100 10/100BaseTX
Fa0/48 notconnect 1 auto auto 10/100BaseTX
Gi0/1 notconnect 1 auto auto Not Present
Gi0/2 notconnect 1 auto auto Not Present
Gi0/3 notconnect 1 auto auto 10/100/1000BaseTX
Gi0/4 notconnect 1 auto auto 10/100/1000BaseTX

Can anyone tell me why the alert mention a non-existent port in the alert?, thanks in advance.

 

Regards,