Activity in Security
Network already exists.
When i try and add my network using the IP that opendns says im on, it says: Network already exists.Im guessing this is because my broadband provider (like most) is on DHCP and it's from someone else and never got released. Can it please be released ...
FMC to cdFMC
I have FMC that is managing two FTDs. I am planning to start using cdFMC. What is the needed licenses for cdFMC. Also, do I need to have the FMC or I can just stop using it.
How To Enable Netflow on FirePower Using FDM
The attached document guides you through configuring Netflow on FirePower using FDM.
Resolved! FPR 2130: Troubleshooting ASP Drops
Hello, We have an FPR-2130 pair (Active - Standby) and I recently see increased ASP Drops (see attached image). It is supposed to be "Flow Denied by access rule, Flow Denied by configured rule".We need to understand better what this is about.How can ...
Unable to edit Umbrella URL white list
I am no longer able to edit our Cisco Umbrella content filter list (default policy?) even though we renewed our subscription in August of 2025.What am I doing wrong?
Cisco ISE Passive Identity Agent on Azure Domain Controller
Hi All, We have a Cisco ISE VM 3.1 version patch 10 which is only used to retrieve user groups from domain controllers in order to enforce the corresponding policies on FTDs. Currently, we have installed Cisco Passive identity agent to all of our on...
FTD installation failure in a Firepower 1120
In the installation of FTD 7.6.2 (recommended version) in a new Cisco Firepower 1120 loaded with ASA v9.20.3. We attempted to reimage the appliance using the console USB port. We downloaded the installation image from the Cisco Software portal (check...
ISE deployment Smart License allocation
Good day everyone We have an old ISE deployment that was registered to a license that will expire in the beginning of December 2025. This deployment is EOL and will be replaced by a new ISE deployment. A new license was procured that will expire in 2...
Need to configure restriction for non compliant wireless user in ise
We have FortiGate WLC for wireless user . After posture scanning if the user is non-compliant we are unable to restrict the access user is getting full access. We tried from ISE to Push ACL still the restriction is not working. Wireless user connecti...
reneval needed for esa c-series appliance help regarding smart lic
Dear All, I need to buy a reneval for ESA C Series (on prem appliance)Die device has older firmware and isn´t connected to smart licence yet.Can you please contact me? German Speaking prefered.
ISE Reporting
I'm using ISE version 3.3 with patch 7 currently. Management want me to submit the posture failed report monthly. I need to generate posture assessment by endpoint and radius authentication report to Excel format. Since it have multiple line for the ...
Internal URL lookup toool
Hi Team, do we have any URL lookup tool in Cisco Secure Internet Access to Verify a specific URL is part of a Destination List.
Re: Reserved IP Address in Cisco Secure Access
Hi, If we purchased a Reserved Egress IP Address in Cisco Secure Internet Access, Is it possible that we route some traffic through reserved IP address some traffic through shared IP address ?
FTD 4100 to 4200 migration in FMC
Hi all. I'm trying to migrate an FMC-managed FTD 4125 HA pair to a pair of FTD 4215s. FMC and all of the FTDs are running 7.4.2.1. Is there any way to migrate the FTD interfaces, routing, etc over to the 4215s? I talked to the TAC and they told me ...
GA Release of API Anomaly Detection and Alerting
Feature Overview: The Cisco Secure Access API is very secure, and also very powerful. We understand that even with all security best practices in place to prevent abuse, it is vital to monitor any anomalies. To support this, we have introduced API...
| User | Helpful Count |
|---|---|
| 47 | |
| 34 | |
| 33 | |
| 22 | |
| 14 |
