Server Networking

My 390 host connected with two cip card,Can I define the virtual mac of two cip as same,So I can implemted load balance. Like this:interface Channel1/2 lan TokenRing 0 source-bridge 10 1 755 adapter 0 4000.0755.9026 lan TokenRing 1 source-bridge 1...

Do all the same rules apply when doing Dlsw redundancy with backup msfc's? For example, do I need the following types of commands:dlsw transparent redundancy-enable xxxx master-priority xand dlsw transparent map local-mac xxxx remote-mac xxxx neigh...

Hi all.Long time reader, first time poster.I'm setting up our cage at our new datacentre here and I'm not sure what setup to use, in regards to switches/routersBasically will have a 1Gigabit connection through a GBIC card.I will have about 3 racks, e...

We would like to implement a VTAM APPN Border Node solution between 2 VTAM hosts that are in separate locations. We are looking to utilize CMPC to each local CIP router, but I am looking for a good example and recommendations and suggestions as to...

I have 2 mainframes. Each mainframe is part of a different logical SNA/VTAm network. Each mainframe has a front end processor ( FEP ). The mainframes communicate with each other through MSNF via a TIC on each front end processor. The communication c...

I have the following setup:Ring1---R1--FW---R2--R3--R4----Ethernet1- There's a AS/400 on Token Ring network connected to R1- There's a AS/400 on the Ethernet segment connected to R4- R1 is a 7200 router, with both ethernet and TR interfaces- R2, R3 a...

We have x25 protocol that needs to be bridge so our cash machines will run at our branches. Our main server is a HP 9000 series, running MPEX. We also have cash dispensers at each of our branches. The cash dispensers run on x25 protocol, therefore, w...

I have DLSw redundancy configured. My circuits often drop from the primary dlsw peer and connect to the backup. I assume it's missing a certain number of responses back from the primary peer. Is there a way to change the timers and cause the route...

i have 1720 router with 8Mb flash and 16 Mdram, i changed the soft then when i reload it decompress the IOS the crach because it haven't memory to load ios.there arn't possibility that router decompress ios directly from flash, without transfert it t...

Hi,We have casual conection to different company. The topology like that:MainframeA(VTAMA-Appl1)--NCPA-- LL--MainframeA(VTAMA-Appl2)--We want migrate our side to router based network like that:MainframeA(VTAMA-Appl1)--CIP--DLUR (DLSW+SnaSw)--LL--Main...

I have a connection like this:pu 2.0---r1--r---r----r------r2----390 r1#sh stunThis peer: 10.1.1.2 *Serial6/1 (group 1 [sdlc]) state rx_pkts tx_pkts drops poll C8 TCP 10.1.2.1 close * 6752...

We are a small school district K-12 We have a 16 site point to points network with a 7206 in the center and 2501s at the remotes, most of the sites have 1/2 of a T-1 (The other 1/2 is muxed voice)while 2 (a HS and the Maint and Ops) have a full T-1,...

Hello there, thanks in advance for your answers.Anyhow, I would like to implement the following on snasw.3 links to Applications: one is via IP (HPR/IP) port and 2 are via DLC port.The Adjacent CP is the same in all 3 cases.I've tried it, but it's wo...

I have to migrate my sna traffic, now direct attach to channel Escon with cpa interface, to qllc with x25 interface to 3745 controller conected to a serial interface of the router.I have to know what x25 bandwidth may I reserve. I can see the cpa tr...

We have a customer that has a s/360 at each end and we are looking at running it over a VPN.What we need to know is the devices that should be on each end to allow them to talk to each other.Does any IOS with the IBM featureset do, like a 1600? If so...