IOS-XR MPLS TE Auto Tunnel Backup Bandwidth Protection Current
Implementation of MPLS TE Auto Tunnel BackupPotential issue with current
implementation of MPLS TE auto tunnel backupEnhancement to MPLS TE auto
backup in IOS XR 7.5.1Supported HardwareConfig ...
we are trying to monitor the Cisco 9148s SFP status, and have get the
Sensor's dBm value from the CISCO-ENTITY-SENSOR-MIB table, meanwile , it
has an Index value like "30000xxxx",such as "30001773",
entsensorValueTable but we can't sure how to locate the ...
Check out our latest release on Cisco Routed Optical Networking
solution. Listen: https://smarturl.it/CCRS8E24Follow us:
https://twitter.com/ciscochampion Disruptive network transformation may
only happen once a decade. First movers can set agendas and fo...
Cisco Champion Radio · S8|E9 Innovations to Achieve a Trustworthy
Infrastructure How do you know for certain that a router in your network
has not been altered with since you deployed it? Wouldn’t it be great if
you can cryptographically challenge your ro...
Hi Everyone, Would like to extend my thanks in advance for anyone
offering assistance. As the subject hints, anyone here know of a way to
convert IOS configs to XR config? I seen and heard about SOX tool but i
am unable to find it. I also tried Cisco Acti...
When I run the command 'sh controllers fabric fia q-depth location
0/0/CPU0' or any 0/X/CPU0 and see the following, what exactly does it
mean? RP/0/RSP0/CPU0:Router#sh controllers fabric fia q-depth location
0/0/CPU0 ********** FIA-0 **********Category: q...
Is this LTE card tied to specific provider such as Verizon or ATT. If I
buy one of these for Verizon carrier, and later decide to move to ATT.
Can I replace the software image to support ATT vendor? or will have to
buy a new LTE card specific for ATT?
Service flow verification and forwarding troubleshooting have just been
made much easier with the introduction of the XR Embedded Packet Tracer
framework. The first platform on which this functionality is supported
is the ASR9000, starting with release 7....
Hi - Can somebody point me to the technical details on how ASR9k
refreshes the ARP cache as the cache timeout is about to expire? We are
trying to understand the exact process and timing of what happens to an
IP to MAC mapping in the ARP cache when the ca...
I'm trying to reset ASR9901, but the options (2 & 3) doesn't seem to
work. When I reset after change, it boots as normal, ignoring nothing.
Also I have to give the option -s (soft) -h (hard) for the reset
command. Is there a different procedure for ASR990...
Cisco Champion Radio · S7 | E32 Cisco 5G Ultra Cloud Core Built for the
Future Cisco 5G Ultra Cloud Core Built for the Future Cisco Ultra Cloud
5G Core solution is an evolutionary jump delivering advanced 5G
features, automation, higher resiliency and dep...
Some of you may have watched the session at Cisco’s first all-digital
Cisco Live and I hope you found it helpful. This is the first in a
series of companion blogs that will later cover in more detail the
topics discussed in the session today. We all know ...
Hi everyone, Below is a link to a video showing how to analyze
traceroute output in L3VPN and look up CEF forwarding and
MPLS/TE/SR/SR-TE forwarding for labels through a domain. Some basic
examples of traffic engineering are used but the concepts lend
Feature Description BGP flowspec in a nutshell is a feature that will
allow you to receive IPv4/IPv6 traffic flow specification (source X,
destination Y, protocol UDP, source port A .. etc) and actions that need
to be taken on that traffic (drop, or polic...
Hi My current active router is a 7200 with a PA-MC-E3 multichannel E3 card to connect our wan branches via ISP to our HQ. I want to replace this router with asr1006 but I am not sure which spa module should I use for E3 multichannel. Regar...
Hello All, I am new to multicast. And I have configured the Cisco XR router with a multicast configuration. Cisco XR is connected with a multicast receiver. and I see the following entries on Cisco XR. There are (*,G) and (S,G) entries. (*, G)'s...
Hello, What is the use of the "static-group" command under "router igmp" in cisco XR?When I configure router igmp interface Loopback0 join-group 188.8.131.52 ! interface GigabitEthernet0/0/0/1 static-group 224.12...
Hello Community members, I've got two ASR1001-X running 16.12.5 with SmartLincensing enabled and the router registered with the CSSM (directly to the Cisco CSSM, not On-Premise SSM). The FLSA1-1X-2.5-20G license is visible in the VirtualAcc...
Hello engineers,I have a question if this feature is fully supported on NCS 540 series. When there is L2 VPN service transporting CDP, VTP, STP etc. for end customer, this feature is useful for troubleshooting. This feature is fully supported on Cata...