Cisco’s security team has released an advisory for: RV340 Series Small Business routers (PSIRT Notice) Fix for bug CSCwc53007- RV34x GUI not accessible – The recommended fix is to upgrade to firmware version 1.0.03.29RV082, RV042, RV016 (PSIRT Noti...
Forum Posts
Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Virtual Assistant - Discover support content and options for your gearSupport page index - Contains a...
We have a SAS model and get routers for testing and creating support documents for our customers. We recently got a RV320 for testing and I must say, this thing is about as cheap and worthless as they come. Not sure what Cisco is doing since I would ...
Dear Community, I came across a shortage of the RV340 that is rather shocking but I hope the reason is my lack of technical knowledge.I set up two VPN tunnels to one ASA.First connects the local RV340 Network 192.168.1.0/24 to the remote ASA network ...
Hi to everybody. I would like to ask if Cisco router 1802W supports DUAL BRODBAND connections by using 2 WAN Interfaces ?1 X PPPOE1X STATIC IP Thank you !!
Hello, We have two office networks(192.168.3.1 and 192.168.10.1) connected through gateway to gateway VPN. We tried to configure static routing on the router at ..3.1 network to route packets to IP range 10.130.78.0/24 through gateway 192.168.10.1. T...
I have a load balanced dual WAN setup on an RV320, and I have one device that I need to exclusively use the WAN2 port, with all other traffic going through WAN1. I've set up the top priority protocol binding with the all traffic service, the device's...
Resolved! Moving from RV042 to RV320
Hello all, As the title states I'm migrating to a RV320 from a RV042. I'd like to minimize the downtime of the network and need to configure the RV320. Is there a way to view the backup Mirror.config file from the RV042 and be able to create a star...
Resolved! RV320 DHCP Status empty
I can't figure it out why on latest firmware I see zero Dynamic and zero Static IP used if in fact those was used
Hi everyone I cant figure it out, why I receive "Connection refused" with SSH port1. I have added rule to "Port Address Translation" I can access to other ports, but this one is not working
I can't figure it out why on latest firmware I see zero Dynamic and zero Static IP used if in fact those was used pls, don't mark this queshion as solved before it will be realy solved
Hi!My router redirect any web(port 80) request (lan user) to it own web management interface . But my web site is accessible form outside networks! The forwarding configuration looks like that:--------------------------- Config ---------------------...
I have a RV325 at one of our office locations and recently I began to notice that the all the logs constantly stop. I can reinitiate the logs by unchecking the options and then saving, followed by checking the desired logging options and then saving...
Hi all:I bought RV110W recently and have a question about SNMP OID:1.3.6.1.2.1.2.2.1.5 (RFC1213-MIB / ifSpeed) &1.3.6.1.2.1.31.1.1.1.15 (IF-MIB / ifHighSpeed)It links at 100Mb speed and the values seems wrong:it's the actual link speed here:And this ...
Hello, I have trouble with importing our certificate (a .pfx file) into our RV340WIt's a wildcard certificate (*.contoso.com). Type: PKCS#12But I always just get an error: Certificat Import Failed What's wrong here? What can I do?
I am getting about 80 Mb/s throughput on my RV325 LAN connections (as measured by iperf) despite the fact that all of the individual ports show that they are gigabit connections, and all of the connected computers likewise show that they are (auto-)c...
Hi So we started to use the IR809, and we also have a switch connect to this setupbut sometimes we just need the switch and a access port. can i make Gigabitethernet 1 to act as a switchport and just assign it a vlan. interface GigabitEthernet0.2des...
