Cisco’s security team has released an advisory for: RV340 Series Small Business routers (PSIRT Notice) Fix for bug CSCwc53007- RV34x GUI not accessible – The recommended fix is to upgrade to firmware version 1.0.03.29RV082, RV042, RV016 (PSIRT Noti...
Forum Posts
Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Virtual Assistant - Discover support content and options for your gearSupport page index - Contains a...
I need to port forward 2 CCTV servers, I have set the Services up and only 1 (.150) works. Below are screen shots of the config. When I try to set the 2nd (.120) to WAN1 the window goes red and will not save. Its probably something simple but I can't...
Hi,I have a RV320 here on a 500/500Mbit fiber line, and don't seem to get more than ~230Mbit througput.If I connect the original modem from the provider, I get 500/500Mbit throughput.Firewall is off while testing.Does the RV320 not provide more throu...
Hi I have three sites connected with RV routers.Site A 192.168.2.0/24 with router RV132W is connected with site to site VPN to site BSite B 192.168.0.0/24 with router RV160 is connected with site to site VPN to site A and CSite C 192.168.1.0/24 with ...
Hello, On my RV345 I am getting daily errors below about the webfilter. I have tried toggling it off and on which resolved for a short while but the error came back so I am not sure what is causing the failure. I have allowed connections to brightc...
Hello,I have the log configured on the RV345 router to send me email alerts with a severity of error and higher. A few times a day I get an alert with the following: <error>dnsmasq: failed to allocate -1 bytes<error>dnsmasq: failed to parse lease da...
I have CenturyLink gigabit fiber at my business and have requested and received a static IP address for site-to-site VPN use. I am using a Cisco RV340 router and it has been working perfectly with dynamic IP. I don't use any sort of Centurylink provi...
Resolved! RV340 behind NAT/Firewall router
Hi We bought two RV340(W) to create a site-to-site VPN, eventually. But for now, we have basic configuration problems.Both RV340 will be behind routers with active NAT/firewalls/DHCP. VPN-Router 1 will be in local network 1 with local IP addresses 10...
Hello, I have a RV345 small business router. I use the Shields Up service from GRC.com to test my router against incoming ports. This service scans ports 0 thru 1055. Under normal circumstances, all ports should show stealth as I do not do any kin...
Resolved! C1116-4P Metered Routes
Hello Everyone, I'm looking at getting the C1116-4P for a branch office. This office will have a layer 2 point to point connection provided by the ISP back to the HQ. One of the ideas being entertained as well is to have a separate Internet co...
Resolved! RV042G bottlenecking on 250MB service.
I have RV042G with firmware v4.2.2.08 (Apr 26 2013 19:12:26). We recently had our ISP remove the 8x T1 service and install a 250MB fiber service. After the installation, when directly connected to their equipment, a speedtest is ran and 250MB speeds...
Hi all,I'm trying to setup an openVPN server on a rV320 router. but the Certificate generator doesn't seem to work.I can generate a self signed certificate without a problem but when i try to enable the openVPN server I cant select it in the "Root Ce...
Hi, I have an RV340 firewall and I configure it with only WAN1.I have to connect it to another third part firewall by using IPSEC s2s.The destination firewall has two WAN and I have configured the s2s with keep alive, DPD and tunnel backup with the w...
I have a static public IP from my ISP, which lives on the RV340 LAN. The RV340 connects to the ISP using DHCP, but the ISP has set up routing protocols such that the internet traffic can be routed to the static IP. I have verified this to work correc...
I have an RV345p (inherited when I got the job).I turned on vlans and gave each its on IP range and VLAN#.They are all subnets of the 10.x.x.x network.Each subnet is 10.10.10.x /24 or 10.20.20.x/24 etc.I select UNTAG for the VLAN that is on that port...
Resolved! RV260 Router Loopback Interface
My ISP need Loopback interface to be configured on RV260-V2 for ISP side health monitoring. has anyone done it?
