Routers - Small Business

I set up my RV042 with two ISPs, one charter internet and the other AT&T DSL.  My DSL modem all of a sudden shows a red light over the "internet" slotshowing that it's not working.  When I remove the modem and hook up to a PC, it works fine.  When I ...

I have a small network setup using:rvs4000 (firmware 2.0.0.3)sg100d-08wap4410n (firmware 2.0.2.1) - configured as APwap4410n (firmware 2.0.2.1) - configured as WDS repeaterWhen I started 3 simultaneous downloads from a Windows 7 machine connected wir...

Hi,Recently the web UI in  my wrvs4400N router becomes inaccessible. When the Ui becomes inaccessible the router  also loses wifi. The strange thingis that router response to pings and computers connected through hard wired still have internet.  I ha...

We have two RV042 configured for gateway to gateway VPN but cannot get any pings across. I have been doing these for years but something is wrong here.  The same RV042 here has a working VPN to another RV042.  The working one is No. 1 in the screen c...

Hi all,I have a question in regards to the 802.1Q intervlan feature on the WRVS4400N. My goal is to setup a test network with atleast 10 departmental VLAN(s). By reading the WRVS4400N's data sheet I know that it supports up to 4 VLAN(s). I decided to...

I have these ports like to block TCP 10001, TCP 36567, TCP 47611, UDP  28086 and UDP 28080, and would like to apply date & time schedule to these port as well.Can you please advise how to set them up in Cisco WRVS4400N.Thanks in advance

Are these the best settings for firewall to achieve VPN pass-through?ENABLE:  Firewall; SPI, DoS attacks; Remote Mgmt; Multicast passthroughDISABLE: Block WAN; HTTPSI need remote management but probably not https for management.  Does multicast passt...

HelloI want to know I can monitor bandwith with SA520Snmp and syslog is activate.but I try à lot of software without any successtahnk u for help

I am attempting to configure my new block of 60 ips with one to one NAT.Everything works as expected until the 5th mapping.  My range of 60 internal ips is mapped to the range of 60 external ips.  When I bind the 5th internal ip to the NIC of my serv...

Our office has an RV016 with multiple WAN connections used to control the 192.168.1.0 lan for user computers. Our phone system however is on a vlan smart switch located at 192.168.5.1. Any device on the RV016 is capable of connecting to any device on...

I purchased this router to accomodate my need to route traffic to multiple internal machines.I have a web server, a conference server etc.I have 5 Public IP addresses and need to be able to route them internally to specific machines.I need to know if...

Hi  I have a RV082 and I used dual wan , every ISP downstream is 10MB/s. two ISP downstream total 20Mb/s.Rv082 use loadblance mode,but total Lan PC download speed was 30kb/s-90kb/s,is very slowly .I find similar question inthe forum ,but i can not .p...

Hi!There a two problems with my WRVS4400Nv2 (Firmware 2.0.0.7) - I use a VDSL 50 internet connection with IPTV (T-Home Entertain):1. Upload speed is very slow: 2048 kbit/s (should be 10000 kbit/s)I deactivated "IPS", bacause the download speed was ar...

Hi, I'm trying to setup a VPN connection between a linux client (OpenSwan) behind a NAT router and a RV042 router with latest firmware.After phase 1 negotiation client sent a UDP 4500 packet but from relevant logs and packet capture looks like RV042 ...

Hi,The Web Interface (GUI) of my SA 540 firewall is not loading. It worked fine the last time. But today when I typed the IP address it simply doesn't load. It did give the security certificate warning as usual though. But when I clicked continue to ...