cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements

Welcome to the Cisco Small Business Community

Have a question? Click on a topic board below to get started in the community.

132978
Views
0
Helpful
30
Replies
dare2tooo
Beginner

Cannot login to 192.168.1.1

                  I want to configure my RVS4000 router but find that I am unable to login to the 192.168.1.1 site to do so. The "admin" username and password is not working. Maybe I do not have to as my internet connection seems to be working fine. Thanks for any help.

30 REPLIES 30
sahilsaifi5969
Beginner
anuragsingh97632
Beginner

Fix to access 192.168.1.1:-

1.  Reset your Router.

> keep your router ON. A reset button is there on the back of your router. Use paper pin and hold that button for approx 20 to 30 second.Unplug everything and plug it again and wit for router to come up.


.2. Check for correct IP address.

> Go to Start button then select Command Prompt.
> Enter “ipconfig” and press the Enter on command prompt.
> In Default Gateway section your IP address is visible.

.3. Check for Network test

> Go to Start button then select Command Prompt.
> Enter “ping with your router IP address” and press the Enter on command prompt.
Eg. Ping 192.168.1.1
> Here you will receive reply from router.

 

I hope this will help 

anuragsingh97632
Beginner

 
RouterLogin92434
Beginner

Hey if you have some problems while while login in 192.168.1.1 than read this article

I hope the problem has been resolve.

- KnowMyRouter.

rajaryan
Beginner

thanks for sharing it. It helped me a lot.

 

nordvpn free trial

jennlyDawn72577
Beginner


I am also unable to connect to my router (192.168.1.1) which I have accessed many times in the past, but for unknown reasons, I can not access it now. I have tried Firefox, IE, and Midori browsers. CISCO/Linksys Wireless-G broadband router (I am connected by blue ethernet cabling from my PC to the router). Stumped why I can not connect to the router. I can pink the router (192.168.1.1) from a Windows 7 PowerShell command line and get packets bounced back from the ping. Browser says "The connection was reset. The connection to the server was reset while the page was loading. The site could be temporarily unavailable or too busy. Try again in a few moments. If you are unable to load any pages, check your computer's network connection. If your computer or network is protected by a firewall or proxy, make sure that Firefox is permitted to access the Web."

Any ideas to fix this?

jennlyc dawn

@jennlyDawn72577 

Hello,

 

What is the model of your router? Did you try to restart?

 

Regards,

Martin

Sophiahelen79795
Beginner


I am running on Windows 7, using a D-Link ADSL DSL-302G (whatever all that is) and have a Linksys WRT350N Wireless router and I am unable to connect to "192.168.1.1".
I am trying to access that site so I can open my NAT. I've reset the wireless router, I've disconnected my modem itself and still nothing. I use my default gateway and that doesn't have any of the things in need to open my NAT, can anyone help me?

jennlyDawn72577
Beginner


When I try to log on to my router good old google won't let me because it is "not secure". I've tried to eliminate everything google from my life but, it is apparently impossible. Anyway, I'm hoping somebody can tell me how to get around this. I tried adding an "s" to the url but then I get "This site can’t be reached 192.168.1.1 refused to connect."

jennlyc dawn

Hi there,

 

What is the model of your router? Can you share a screenshot from the error login page?

 

Regards,

Martin

fmarshall
Beginner

Often it's a matter of using the right format of the address in your browser:

I'm assuming that the router interface IP is 192.168.1.1 - if that's not right then you have to use what *is* right.  Here are some examples:

192.168.1.1.

https://192.168.1.1:8080 where 8080 is the PORT number to be used.
https://192.168.1.1:443/

http://192.168.1.1:80/
http://192.168.1.1:81/
http://192.168.1.1:8008/



I'm not trying to provide an exhaustive list here - but these port numbers are common.

So, combining https with likely port numbers and/or http with likely port numbers is the idea.

Usually Cisco can help with this.

I've found this to be absolutely necessary after updating firmware on some Cisco routers.

rajaryan
Beginner

You can also check logging on 192.168.1.1 IP address (if your router supports that). And for the password, you can follow this guide to retrieve your password

router-wifi
Beginner

Another option should be to find the correct dhcp ip address four login to router admin interface. https://19216811.how/wiki-how-to-find-true-router-IP-address go to here for your operation system information.

leoliang2021
Beginner

192.168.1.1 is the default login path of many routers, some of which are 192.168.0.1. The login paths of different models are different. For example, the login paths of tp link archer ax90 and ASUS router are different