RV042 and no-ip.com

[axiontiCisco]

I recently purchased a RV042 device but when I tried to set my DDNS account I realized that the only two providers are dyndns.org and 3322.net. We already have an account in no-ip.com and several services using the no-ip.com host.

How can I set up a no-ip account in my rv042?

Regards and thanks for your help.

[Calin C.]

Hello

I couldn't find any "trick" to force it to use no-ip.com with it. I'm sorry to say, but should have read the specifications before purchase:

http://www.cisco.com/en/US/prod/collateral/routers/ps9923/ps9925/data_sheet_c78-501225.html

Regards,

Calin

[axiontiCisco]

Thanks Caling.

[axiontiCisco]

What if I install the no-ip client (DUC) in one of my server?

We use Dual-WAN in load balance mode. The problem is that when the no-ip client updates, it will be reporting WAN1 IP and/or WAN2 IP. Is there any way to avoid this behaviour?

Regards

[Calin C.]

If you install the client will work, but you'll have the problem that you said.

Maybe you can prioritize one provider over the other so always use the same exit point.

Otherwise you'll have the exit IP registered on no-ip.com.

HTH,

Calin

[itelcomsa]

Cisco IOS versions 12.4 and later have the capability to directly update your No-IP hostname using a built-in DDNS client. If you have a Cisco router with the latest firmware, this support is already built into it. We offer these examples below for informational purposes only and recommend that router configuration changes be made by qualified personnel to minimize the risk of losing Internet connectivity or causing other damage to the router.

SUMMARY STEPS

1. enable
2. configure terminal
3. ip ddns update method method-name
4. ddns [both]
5. internal name-cache
6. http
7. add url
8. remove url
9. interval maximum days hours minutes seconds
10. exit
11. exit
12. interface interface-type number
13. ip ddns update hostname hostname
14. ip ddns update method method-name
15. exit

DETAILED STEPS

	Command or Action	Purpose
Step 1	enable Example: Router> enable	Enables privileged EXEC mode. Enter your password if prompted.
Step 2	configure terminal Example: Router# configure terminal	Enters global configuration mode.
Step 3	ip ddns update method method-name Example: Router(config)# ip ddns update method myupdate	Specifies the update method name.
Step 4	ddns [both] Example: Router(DDNS-update-method)# ddns	Configures DDNS as the update method and enters update method configuration mode. The both keyword specifies that both A and PTR RRs will be updated. Note You can specify DDNS or HTTP but not both in one step. If you have specified DDNS, you must disable it by using the no ddns command before you can configure HTTP. For the HTTP configuration, see Steps 5, 6, and 7.
Step 5	internal name-cache Example: Router(DDNS-update-method)# internal mycache	Specifies that an internal cache will be used as the update method.
Step 6	http Example: Router(DDNS-update-method)# http	Configures HTTP as the update method and enters DDNS-HTTP configuration mode.
Step 7	add url Example: Router(DDNS-HTTP)# add http://username:password%40dynupdate.no- ip.com/nic/update%3Fhostname= hostname.yourdomain.com	Configures a URL that should be invoked in order to add or change a mapping between a hostname and an IP address. The following example of a URL specifies adding or changing the mapping information using No-IP.com: http://username:password%40dynupdate.no-ip.com/nic/update%3Fhostname=hostname.yourdomain.com. You have to input the URL string noted above. Alternatively, you can use the URL string http://username:password%40dynupdate.no-ip.com/nic/update%3Fhostname=&myip=The special character strings and will be substituted with the hostname to update and the IP address with which that hostname should be associated, respectively. Note: Use the html encoding of %40 for the "@" symbol and %3F for the "?" symbol or IOS will complain.
Step 8	remove url Example: Router(DDNS-HTTP)# add http://username:password%40dynupdate.no-ip.com/nic/update%3F hostname=hostname.yourdomain.com	Configures a URL that should be invoked in order to remove a mapping between a hostname and an IP address. The URL takes the same form as the add keyword in Step 6.Note: Use the html encoding of %40 for the "@" symbol and %3F for the "?" symbol or IOS will complain.
Step 9	interval maximum days hours minutes seconds Example: Router(DDNS-HTTP)# interval maximum 1 0 0 0	Configures a maximum update interval. The arguments are as follows: daysRange is from 1 to 365. hoursRange is from 1 to 24. minutesRange is from 1 to 60. secondsRange is from 1 to 60.
Step 10	exit Example: Router(DDNS-HTTP)# exit	Exits to update-method configuration mode.
Step 11	exit Example: Router(DDNS-update-method)# exit	Exits to global configuration mode.
Step 12	interface interface-type number Example: Router(config)# interface ether1	Enters interface mode.
Step 13	ip ddns update hostname hostname Example: Router(config-if)# ip ddns update hostname hostname.yourdomain.com	Specifies a host to be used for the updates. The update will associate this hostname with the configured IP address of the interface. The hostname argument specifies the hostname that will receive the updates (for example, yourdomain.com).
Step 14	ip ddns update method method-name Example: Router(config-if) ip ddns update myupdate	Specifies the name of the update method to use for sending Dynamic DNS updates associated with address changes on this interface.
Step 15	exit Example: Router(config)# exit

[paolo bevilacqua]

Wrong forum, post in "small business - routers". You can move your post using the actions panel on the right.