ANNOUNCEMENT - The community will be down for maintenace this Thursday August 13 from 12:00 AM PT to 02:00 AM PT. As a precaution save your work.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements

Welcome to the Cisco Small Business Community

Have a question? Click on a topic board below to get started in the community.
Get the latest news in this issue of the Cisco Small Business Monthly Newsletter

686
Views
0
Helpful
8
Replies
Highlighted
Beginner

RV320 1.2.1.13 internal network access bug

Setup:

Dual wan in auto mode with 4 vlans and 4 networks. wan 1 default gw. NSD not used at all.
Protocol binding table used to force traffic from Network 1 via WAN1. Traffic from network 2,3,4 forced via WAN2.

Network 1. 192.168.1.0/24 vlan 1 on lan port 1 untagged (port 2,3,4 excluded) Device management enabled
Network 2. 192.168.2.0/24 vlan 20 on lan port 2 untagged (port 1,3,4 excluded) Device management disabled
Network 3. 192.168.3.0/24 vlan 30 on lan port 3 port (port 1,2,4 excluded) Device management disabled
Network 4. 192.168.4.0/24 vlan 40 on lan port 4 (port 1,2,3 excluded) Device management disabled

One-to-One NAT external ip's on wan 1 to internal ip's on vlan 1

On fw 1.1.1.19 you could correctly access port 80 and 443 on computers on network 1 from network 2,3,4 via the external ip on wan 1.

The problem: With 1.2.1.13 firmware you get the RV320 login page whenever you try to access a computer on network 1 on port 80 or 443 instead of being redirected to the computer on network 1.

Please fix asap.

1 ACCEPTED SOLUTION

Accepted Solutions
Highlighted

Hi, I had network problems

Hi, I had network problems too after upgrading the firmware to 1.2.1.13.

Release Notes state that the configurations between 1.1.1.19 and 1.2.1.13 are NOT compatible.

 

I was able to resolve my issues by performing the following steps: 

- Upgrade firmware to 1.2.1.13

- Reset router to factory default so that all configurations are deleted.

- Manually re-configure the router. Do not use any configuration file from old 1.1.1.19 firmware version!!

 

My RV325 is working fine now.

 

 

 

View solution in original post

8 REPLIES 8
Highlighted

Hi, I had network problems

Hi, I had network problems too after upgrading the firmware to 1.2.1.13.

Release Notes state that the configurations between 1.1.1.19 and 1.2.1.13 are NOT compatible.

 

I was able to resolve my issues by performing the following steps: 

- Upgrade firmware to 1.2.1.13

- Reset router to factory default so that all configurations are deleted.

- Manually re-configure the router. Do not use any configuration file from old 1.1.1.19 firmware version!!

 

My RV325 is working fine now.

 

 

 

View solution in original post

Highlighted
Beginner

Both routers already factory

Both routers already factory reset after upgrade and manually configured so this is not it.

Highlighted
Cisco Employee

Hello Bitspaceab,I'll lab

Hello Bitspaceab,

I'll lab this up and see if I can recreate your scenario on the new firmware. Quick question, do you have remote management and https enable on the RV320 please?

Highlighted
Beginner

If i disable HTTPS i takes

If i disable HTTPS i takes over HTTP Port 80 instead so I cant reach computers on port 80 from network 2,3,4 on network 1.

Remote management doesn't matter.

I can send you the config from 1.1.1.19 and 1.2.1.13 if you want. Both have been factory reset and manually configured after upgrade. But config should be identical.

Highlighted
Cisco Employee

My email is maharbin@cisco

My email is maharbin@cisco.com. Please feel free to send them. The reason I asked about remote management is if enabled, by default, it uses 443. 

Highlighted
Beginner

I have opened a case with

I have opened a case with cisco small business support and talked to Dean Pillard who has the configs. Do you want them anyway or can you check with Dean directly?

Highlighted
Cisco Employee

Dean is more than capable of

Dean is more than capable of assisting you. I am interested in the outcome however. Will you please ping the case number to my email so I can follow? Thank you.

Highlighted
Beginner

email sent

email sent