VPN Tunnel issues with RV120W logs

gwhitten · ‎12-11-2012

I have setup a Client with a RV120W to have access to a IBM System i server. The connection will stay up for a while and then fail. I am unable to "DROP" the connection and reconnect. I have to disable the VPN tunnel and then do an edit process even though I don't actually change anything. I enable the tunnel and then I can connect the VPN tunnel again. I do not have access the Cisco ASA that it it connects with so I cannot give the settings for it. I suspect there is not a problem with the ASA configuration as it does work but will not stay connected. Below is the configuration information for the RV120W.

System Information

==============================================

Host Name : routerBBE424

Firmware Version : 1.0.4.10

Firmware MD5 Checksum : bbe601c388c75979368523e575c6b8b3 PID VID : RV120W-A V01

LAN (Local Network) Information

==============================================

MAC Address : F0:F7:55:BB:E4:24

IPv4 Address : 192.168.96.2 / 255.255.255.0

IPv6 Address :

DHCP Server : Enabled

DHCP Relay : Disabled

DHCPv6 Server : IPv6 is disabled

WAN (Internet) Information

==============================================

WAN (Internet) Information (IPv4)

==============================================

MAC Address : F0:F7:55:BB:E4:25

Connection Time : 0 Days 12:59:04

Connection Type : Static

Connection State : Connected

IP Address : 10.0.0.3

Subnet Mask : 255.255.255.0

Gateway : 10.0.0.2

Primary DNS Server : 10.0.0.2

Secondary DNS Server : 66.175.131.21

NAT (IPv4 Only Mode) : Enabled

WAN (Internet) Information (IPv6)

==============================================

Connection Time : Not Yet Available

Connection Type : DHCP

Connection State : Not Connected

IP Address : fe80::f2f7:55ff:febb:e425/64 Gateway :

DNS Servers :

Wireless Information

==============================================

Operating Frequency : 2.4GHz

Wireless Network Mode : B/G/N-Mixed

Channel : 1

VPN settings from configuration with remote site X out.

IpsecIKEPolicy = {}

IpsecIKEPolicy[1] = {}

IpsecIKEPolicy[1]["Direction"] = "0"

IpsecIKEPolicy[1]["EncryptionAlgorithm"] = "2"

IpsecIKEPolicy[1]["LocalIdentifier"] = "10.0.0.3"

IpsecIKEPolicy[1]["ExchangeMode"] = "0"

IpsecIKEPolicy[1]["RemoteIdentifier"] = "66.175.xxx.xx"

IpsecIKEPolicy[1]["Presharedkey"] = "09B9344D39D54F9CD6D9*"

IpsecIKEPolicy[1]["IKEPolicyName"] = "Choctaw_CH"

IpsecIKEPolicy[1]["LocalIdentifierType"] = "0"

IpsecIKEPolicy[1]["SALifeTime"] = "86400"

IpsecIKEPolicy[1]["DPDDetectionPeriod"] = "15"

IpsecIKEPolicy[1]["ModeConfigStatus"] = "0"

IpsecIKEPolicy[1]["XAUTHType"] = "0"

IpsecIKEPolicy[1]["DPDFailureCount"] = "4"

IpsecIKEPolicy[1]["AuthAlgorithm"] = "2"

IpsecIKEPolicy[1]["AuthType"] = "0"

IpsecIKEPolicy[1]["DHGroup"] = "2"

IpsecIKEPolicy[1]["DPD"] = "1"

IpsecIKEPolicy[1]["_ROWID_"] = "1"

IpsecIKEPolicy[1]["RemoteIdentifierType"] = "0"

IpsecVPNPolicy[1] = {}

IpsecVPNPolicy[1]["EnableKeepAlive"] = "0"

IpsecVPNPolicy[1]["LocalSubnetMask"] = "255.255.255.0"

IpsecVPNPolicy[1]["EncryptionAlgorithm"] = "2"

IpsecVPNPolicy[1]["AuthAlgorithm"] = "2"

IpsecVPNPolicy[1]["RemoteNetworkType"] = "3"

IpsecVPNPolicy[1]["AutoPolicyType"] = "0"

IpsecVPNPolicy[1]["LocalGateway"] = "0"

IpsecVPNPolicy[1]["RVGStatus"] = "0"

IpsecVPNPolicy[1]["VPNPolicyName"] = "Choctaw_CH"

IpsecVPNPolicy[1]["LocalStartAddress"] = "192.168.96.0"

IpsecVPNPolicy[1]["Status"] = "1"

IpsecVPNPolicy[1]["Netbios"] = "0"

IpsecVPNPolicy[1]["KeepAlivePeriod"] = "10"

IpsecVPNPolicy[1]["PFSKeyGroup"] = "0"

IpsecVPNPolicy[1]["RemoteStartAddress"] = "10.6.1.0"

IpsecVPNPolicy[1]["IKEPolicyName"] = "Choctaw_CH"

IpsecVPNPolicy[1]["SPIOut"] = "0x"

IpsecVPNPolicy[1]["KeepAliveFailureCount"] = "3"

IpsecVPNPolicy[1]["LocalNetworkType"] = "3"

IpsecVPNPolicy[1]["SALifeTime"] = "4608000"

IpsecVPNPolicy[1]["RemoteSubnetMask"] = "255.255.255.0"

IpsecVPNPolicy[1]["PolicyType"] = "1"

IpsecVPNPolicy[1]["RemoteEndPoint"] = "66.175.xxx.xx"

IpsecVPNPolicy[1]["NodeId"] = "1"

IpsecVPNPolicy[1]["SALifeTimeType"] = "1"

IpsecVPNPolicy[1]["Rollover"] = "0"

IpsecVPNPolicy[1]["SPIIn"] = "0x"

IpsecVPNPolicy[1]["RemoteEndPointType"] = "0"

IpsecVPNPolicy[1]["_ROWID_"] = "1"

IpsecVPNPolicy[1]["FailbackTime"] = "30"

Receiving the following messages as well but not sure why. Any suggesstions to resolve?

[rv120w][Kernel][KERNEL] printk: 3 messages suppressed.

[rv120w]Tue Dec 11 11:48:37 2012(CST)