cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements
Community

Please be advised, the GuideMe Wizard is no longer available on the Small Business Support Community. For search capability please use the community search field to find content related to Cisco Small Business documents, videos, and discussions.

SPA500 series report rule

1927
Views
0
Helpful
1
Comments

Hi All,


 I've tried to set up the report rules on an SPA504G (7.6.2e). I've read the article about provisioning and some article from community. The conclusion is that the documentation is not up to date.

 From the documentation
The possibilities:
tftp://tftp_server_address/config_$MA.xml
[--status]tftp://tftp_server_address/status_$MA.xml
[--delta]tftp://tftp_server_address/delta_$MA.xml
[--content a]tftp://tftp_server_address/book_$MA.xml
[--content p]tftp://tftp_server_address/config_$MA.xml
[--content h]tftp://tftp_server_address/hitory_$MA.xml


You can use more rules separat them with semicolon (;), like this: "[--delta]tftp://tftp_server_address/delta_$MA.xml; [--content a]tftp://tftp_server_address/book_$MA.xml"


In the real
You should not use semicolon (;) because the SPA will add it to the end of the filename.
<Report_Rule group="Provisioning/Configuration_Profile">[--status]tftp://tftp_server_address /status_MAC.xml; [--content a]tftp://tftp_server_address /book_MAC.xml</Report_Rule>
spa_address → tftp_server_address TFTP 107 Write Request, File: /status_MAC.xml;, Transfer type: octet, blksize=126, timeout=10, tsize=x
spa_address → tftp_server_address TFTP 107 Write Request, File: /book_MAC.xml, Transfer type: octet, blksize=126, timeout=10, tsize=x


 You can't use more than two rules.
<Report_Rule group="Provisioning/Configuration_Profile">[--content p]tftp://tftp_server_address /config_MAC.xml [--status]tftp://tftp_server_address /status_MAC.xml [--content a]tftp://tftp_server_address /book_MAC.xml</Report_Rule>
spa_address → tftp_server_address TFTP 107 Write Request, File: /config_MAC.xml, Transfer type: octet, blksize=126, timeout=10, tsize=x
spa_address → tftp_server_address TFTP 152 Write Request, File: /status_MAC.xml [--content a]tftp://tftp_server_address/book_MAC.xml, Transfer type: octet, timeout=10, tsize=x


 If you want to backup the whole configuration without bracket and the status, you should put the rule without bracket to the end.
<Report_Rule group="Provisioning/Configuration_Profile">[--status]tftp://tftp_server_address /status_MAC.xml tftp://tftp_server_address /config_MAC.xml</Report_Rule>
spa_address → tftp_server_address TFTP 107 Write Request, File: /status_MAC.xml, Transfer type: octet, blksize=126, timeout=10, tsize=x
spa_address → tftp_server_address TFTP 107 Write Request, File: /config_MAC.xml, Transfer type: octet, blksize=126, timeout=10, tsize=x


 If you want to backup the address book and the status but the address book is empty the second rule won't be executed.
<Report_Rule group="Provisioning/Configuration_Profile">[--content a]tftp://tftp_server_address /book_MAC.xml [--status]tftp://tftp_server_address /status_MAC.xml</Report_Rule>
No tftp log


 When the tftp server does not response to the writing request and the SPA receive a new SIP NOTIFY message the SPA freezes. In this case the power cable should be removed.

Can anyone use report rule?

Regards,

Szabolcs

Comments
Engager
You has created document, not the discussion. Create new discussion in Voice Systems.
CreatePlease to create content