We recently announced the release of our self-serve virtual assistant. You can read the full announcement here. Videos and documents are available within a click for our latest products. Once you've told the bot what device you're using, the context ...
Forum Posts
(Updated September 2023 - Added Catalyst 1200 and Catalyst 1300 ) Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Catalyst 1200 & 1300 Hardware Install...
Folks I m super frustrated. i thought by getting the cisco RV340 router it will solve my problem by allowing me to create a static NAT for my private vLANs to access internet.when connecting the RV340 router i got my ISP IP and created the needed v...
I am the tech guy at a small school. I recently switched out our very old Cisco switches for Cisco SG300-20 switches.After doing so, I now find that all of my wireless access points give connection speeds where the download speed is significantly slo...
Implementing changes to my network infrastructure, which will require me to update my documentation. Do we know when the Visio Stencils for the SG350XG-24F & SG350X-48 switches will be released? I've checked through the https://www.cisco.com/c/en...
hey i have problem with SG300-10 (SRW2008-K9 V05), its boot as SF300-08, i try to put newest FW and bootfile thru xmodem, nothing happend, its always boot as SF300-8. How to boot it as SG300-10?
Resolved! SG350-52P inter VLAN configuration issue
Hello,I'm trying to configure a SG350-52P (my first time...), running with the latest frimware.I've configured 2 VLAN. I want to use VLAN1 for all the PC of the office and the other for the router. Only one interface uses VLAN2 (GE24)I've also confi...
Hello, i have a problem on my Switch SG300 28 PP, here is the message that i get on console: 10-Oct-2013 17:27:18 %HAL_config_poe-A-POEFailDetected: POE ERROR(i2c_write_mem failed. addr 0x1326 dev_num 1 val 0x14) was detected: POE is Disabled untill ...
Hi,I am trying to install SG350 switch for the first time.I have Trunk coming from SG500 and is connected at port no. 24 on my new SG350 switch.On SG350 I wish to configure 2 VLANs exist on SG500 i.e. VLAN 17 & VLAN18VLAN17 has ip address 192.168.17...
Dear Cisco, Currently on my Catalyst 2960 VLAN is assigned to a network port through SNMP using the following oid: 1.3.6.1.4.1.9.9.68.1.2.2.1.2. (IFACE)This allows me to reap the associated VLAN ID, and exploit it.I am looking for an OID allowing m...
Hello All, AP (1702i) is not discovering WLC while connecting on SG350-10P Gb PoE Managed Switch. But if I connect the same AP (1702i) on Cisco cat 3560cx switch it has no problem discovering WLC. I am attaching the logs here for reference.What i am...
This is my first go at private VLANs for a customer. I've looked at the sample documentation and it appears fairly straightforward. But I've run into an issue where I do not understand how to get a DHCP scope associated with them. I have a private...
We have a network of 6 switches and are adding a 7th. 5 of the existing 6 are SG300 units and 1 is an old L3 Catalyst which is currently the gateway. We tried to add another SG300-52P today but whenever we plug it in, the rest of the switches stop ...
I have 2 stack sg500 and I have changed the enable password on the devices. The 2 devices use the same password. After i made the change I can logon on to the devices with the standard username account and it logs into devices and gives me config-t a...
Resolved! SG220-26P - 802.3af mode A
Hi all, I'm about to buy SG220-26P switch. I have some other vendor access point which supports 802.3af mode A. Does SG220-26P support only mode A or only mode B, or it supports both? Most important question: will this other vendor access point work ...
Hello Community,after updating the switch from 2.4.5.71 to 2.5.0.83 the following issue occured: First the auto negotiation between the switch and a client works fine and the port comes to live with 1Gbit -- after a period of time the the switch goes...
Dear all, Recently I noticed that since the latest available firmware version (1.4.10.6) was released, the 802.1x port based authentication is not working properly for my printer which is configured to use MAB identification. I simply can't see any a...
