Switches - Small Business

Hello, I have an SG 300 configured with 3 VLANs (in L3 mode) and my router is connected with the switch. I can not access internet from my VLANs except VLAN 1 with following IP assignments. PLEASE HELP. 1) - Router IP - 192.168.1.1    - Router LAN ...

Hi, I have two Cisco SG300 28P switches and one SF300 24P Switch. One of the SG300 Switches acts as a core switch (Core) The other two are (SG300-2) and SF300-1 and both are connected to the core switch. SG300-2 GE25 Links to port GE26 on the Core...

Hello I need to resolve a situation. I´m connecting a Switch Cisco Small Business SG200-50 with a Juniper SRX100, I can to access to switch cisco without restrictions, but the Juniper is owned from a provider, they give me the the connection to inter...

Hello I need to resolve a situation. I´m connecting a Switch Cisco Small Business SG200-50 with a Juniper SRX100, I can to access to switch cisco without restrictions, but the Juniper is owned from a provider, they give me the the connection to inter...

Hi We have a Cisco SF300-08 which I have owned for a few years.  It has been in a location where we could not rack mount it, now I wish to move it into our rack infrastructure but have lost the mounting brackets. I can't seem to find them to purcha...

I have an SG300-10P that is connected to a 3560G switch via port 10. The log from SG300 is full of these duplicate IP messages:Nov  4 11:05:03: 10.1.1.49 NOTICE    %IPADTBL-N-IPDUPLICATE: Duplicate IP address 10.1.1.49 from MAC c8:f9:f9:da:e2:81 was ...

Hi, I have an SF300-24P running SW version 1.4.5.02 (latest avail) which has tree DHCP pools configured [1]. The switch is running in switch mode (L2). It has the management IP address 172.17.129.2 on VLAN 129. I have a linux router running dhcrelay ...

I'm trying to modify the vlan membership on a port and when I click the join vlan membership button a pop-up shows up but it is very minimized and when I resize it so I can see everything the area where there should be a list of my vlans there is not...

We have 2(two) SG300-28 switches. We have several VLANS that need to be truked between switch A and switch B 1. We are able to create 1 TRUNK port  that includs vlan 2,3,4 and it works fine between switch A and B.  We are now trying to create a 2nd T...

Hello, I'm pretty new to networking and managed to get hold of an SG200 and some other hardware. The rest appears to be working perfectly, however the SG200-18 seems to reboot every 12 seconds. The power light flashes continually (I assume normal f...

Hello, is it possible to install this Switch inside a 10" Rack? Are there any accessories available to do this? Thanks for answering Meik

Hai team,                 My name is arun . I have one issue. Please help me using your valuable advice. I have one Scenario . We have two cisco switches sg 300 and two firewall Sophos UTM 230. One fire wall is master and other is slave for high ava...

Hi All, Have you ever seen below message on SG500 switch before ? Jul 12 04:21:18 atviesw01 1 2016-07-12T02:21:17Z atviesw01 SYSLOG - OSFATAL - %SYSLOG-F-OSFATAL: FATAL ERROR: GOAH: ABORT DATA exception ***** FATAL ERROR ***** SW Version : 1.4.5.02...

hi  i am trying to stack 2960S and X . Looks like its compatible for stack, I am not sure why stack is not getting formed. Your help is greatly appreciated

Hi, i've a Linksys SGE2000P switch witch had original firmware 1.0.0.45. I've upgraded the BOOT Software Version to 2.0.0.03 successfully via xmodem than i've tried to push firmware 3.0.0.17 also the same way witch went successful also but when reboo...