We recently announced the release of our self-serve virtual assistant. You can read the full announcement here. Videos and documents are available within a click for our latest products. Once you've told the bot what device you're using, the context ...
Forum Posts
(Updated September 2023 - Added Catalyst 1200 and Catalyst 1300 ) Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Catalyst 1200 & 1300 Hardware Install...
Resolved! Login to SNA failed
I bought an SG350-10 switch and updated the firmware version to 2.3.5.63. After setting up the switch including setting a new password for the default user "cisco"i noticed that i can't login to the "Smart Network Application" (SNA). Logging in t...
Hi guys,I stumbled upon a problem and hope you can help me with that - but I fear it's a bug...I'm using two stacked SG550X as core with IPv4 Routing enabled. A few months ago I've configured some ACLs that were working like a charm - until I added o...
Dear Sir,Please help us to check the warranty status of Cisco switch by serial number cisco switch model - CBS350-24P-4G V02 S/N FOC2527L7R7
Hello,I purchased two CBS350-48P-4G switches for a project, we are running some A/V equipment through one of the switches and we have Sonos equipment connected. This is know to cause Multicast storm traffic and degrades the network. Our automation ...
Hi There, I've got a bit of a weird issue - I have the unique requirement to rate limit a couple of access ports on a Cisco CBS350 switch for one of our customers. I've tested the config on a couple of switches we keep around for testing, and am see...
Resolved! Layer 2 routing question
In my lab, I have 2 Cisco SG350-10 switches connected to a Palo Alto 220 firewall. On my switches, I want to do layer 2 switching and routing on the firewall. Here is my setup: SG350-10 switch #1ports 1-3 VLAN2 set as access portsports 4-6 VLAN4 set ...
Hello to all,I'm opening this thread because I have a problem with one of my switches cisco small business CBS250.I have different VLANs configured with access ports.Unfortunately when I connect a certain type of ehternet equipment it switches my acc...
What is the CLI command to do the following: 1) set all the ports to have vlans 1-2, with vlan 1 (default) untagged, vlan 2 (VoIP) tagged 2) set the PVID of all ports to vlan 1 (is this necessary on sg350??), this is how our older sg300s are configur...
Hello to all, I have an issue with a Catalyst 5548, Rel. 17.6.04. After installing the IOS and installing the golden image the switch doesn't boot any more. The switch starts the boot sequence with "initializing the hardware" stops afterwards and sh...
Hi I have a cisco cbs350 that is connected to a router that provided an IP range that I did not want. The VLAN1 is directly connected to the router with DHCP. 10.1.10.x I changed this so the switch would provide the DHCP.I created new VLANs 10, and ...
Hi, Recently we bought a CBS350-48T-4X for Enterprise use. Sometimes the switch will become lag and the ping will spike to a high latency even pinging to the local gateway. We also did a cpu utilization command and surprisingly it shows almost to 100...
Resolved! PNP Server Quiestion
Hello all, sorry for the total newbie question but are the following messages anything to be concerned with? There are two switches on the stack. 1. CBS350-48T-4X, 2. CBS350-48P-4X. Thanks so much in advance!Stack3Master#18-Dec-2022 16:39:38 %PNPAGEN...
I changed my gateway address in my DHCP scope. All the leases had been set to indefinite previously. My iPhone stopped working later in the day in that it could never acquire an IP Address so it would never acquire the wifi SSID. I went into the ...
I just deployed a CBS250-16P-2G in an office environment and the (what I am pretty sure is) transformer noise is pretty bad. Its a continuous high pitched buzz and the users near it are being driven crazy. I am probably going to seek replacement, but...
As SG300-28 @28 Port Gigabit L2 Manageable Switch declaired as EOL Support, So replacement product required.How to process for RMA of this product?
