Switches - Small Business

Hi,Does someone happen to know how to forward or share Bonjour and/or UPnP traffic from one VLAN to another?I have a SAN that uses a seperate storage VLAN. But I want to be able to take some advantage of the multimedia features and such. This works m...

Hi,I am planning to purchase a 48 port 10/100 switch and 2 Gigabit Uplink ports. Just want to ask what is the computation for Link Aggregation? For me to be able to know if I will consume the Aggregated Link of the two Uplink Ports. Just curious on t...

could use some advise on the best way of setting this up correctlyI am in the process of preping our network for the installation of an IP Camera based security system on it will be running within VLAN 600 in our network, and management would prefer ...

3 Network Engineers later. . . I'm appealing to these boards for ideas. Situation:Rolling out new Avaya POE VOIP phone system for our corporate office.  Existing Infrastructure:1 Core Cisco 3560 connected to 7 Cisco 2960 with ethertrunking enabled an...

Our SGE2010 switch is accepting connections using SSLv2 (according to the PCI compatibility scanner)Is there a way to prevent it from accepting / responding to connections using this version of SSL but still allowing connections using SSLv3 or TLS?If...

Hi, We have a small problem with ESW500 serie Switches.We save configuration on each one with the web interface -> Maintenance -> File Management -> Copy Configuration File -> HTTP -> BACKUP.We obtain a text file running-config.txt.Now we want to res...

Dear All,The 48 port ethernet linksys switch is not saving the configuration after reboot.Soft and hard reboot tried but still problem exist.Any suggestions are welcomed.

Cannot get the SG200-8 to mirror any traffic other than ping (icmp).Factory default settings, with port 7 src to port 1 dst on session 1.Pings mirror just fine.  But other traffic. such as web and ssh, is not being mirrored.FW version 1.0.2.0

Hi everyoneI am new to VLANs and Cisco SMB switches. I have a new SGE 2010P switch and i am trying to configure different VLANs, one for data, one for Voice and the other for server.Is there any tutorial on how to configure VLAN, by the way i tried t...

Hi all! I have a problem with switches SPS208G2. They're conected with SFP module after Linksys SPS224G4 and another swithes. After reboot switches which are conected with SPS208G2 don't see link. However previous switches phisical link status is up ...

Hi thereJust had a very weird problem with our nearly brand-new (less than 1 months old) SF 200-24P 24-Port PoE Smart Switch. We are using this switch for 9 IP phones. It has been working fine for just over a week, and now 7 of that 9 phones all of s...

I'm trying to setup an ACL on my SG300-20 to enable FTP and a few other protocols to a server, but I'm running data that returns on different ports (ie active FTP).Below is a sample:-------------------------------------------Extended IP access list P...

Hi all,I'm hoping someone can provide a little insight as to the difference between the SLM2008 and the SLM2008T-NA.If the SLM2008 and SLM2008T-NA are basically the same switch and I’m assuming they use the same documentation for both of then why don...

Hello out there,I have a strange problem occurring in our office. Essentially, not all ports on our brand new SG300-28P switches provide Inline Power to our older 7900 series phones. I can connect the phone a couple ports down and it usually powers u...

Hi,I have a very strange problem with all of my Cisco ESW 540 switches. I have a three 48ports switches on my network, and I've noticed that when I use Desktop smartport profile for my workstations I'm not able to upload file to the youtube. I can up...