We recently announced the release of our self-serve virtual assistant. You can read the full announcement here. Videos and documents are available within a click for our latest products. Once you've told the bot what device you're using, the context ...
Forum Posts
(Updated September 2023 - Added Catalyst 1200 and Catalyst 1300 ) Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Catalyst 1200 & 1300 Hardware Install...
Hello, I have the following problem with my SG500X switch.It is stuck in a boot loop and does not respond to "Enter or ESC" in the consoleHere is a picture of the bug I have already tested various proposed solutions, including this one.Unfortunately,...
Hi,I have one SG350X 10Gb switch trunked from its 10Gb SFP+ XG04 port to an SG350 1Gb LAN switch port (GE07)I have a SMB server running behind the SG350X in a dedicated VLAN. InterVLAN routing is done at the SG350 level.The setup is working perfectly...
Hi, I need help for Cisco RV160W router WAN QoS profile configuration change for Low default to Highest Please help me how to configuration QoS. I am using two Cisco SF300/24 connected with RV160W. Please make screen shoot image and step by step How ...
I have cisco SF300 Switch, how i configure to each PORT 1-24 and all MAC QoS DSCP value 6Mbps and LAG Port Channel for every AP 6Mbps, I need more dozens Cisco SF/SG Series Switch for my Networks. I need easy to manage Bandwidth.Foysal ISP Broadband ...
Good afternoonWe are presently looking to standardize out infrastructure to use Cisco Catalyst switches, exclusively. We presently have 1 3560, and a WS-C2960-24PC-L. These switches feed a stack of netgear switches (which we want to get rid of).Our...
Hi there, as my title states, I am a new IT manager.I took over the position from the previous manager just a few days ago and am running on zero docs or SOP's. I am here because I have 4 Cisco SD500X-48P layer 3 switches that were setup and I need h...
Hi team, Someone know I can fin the ROM of the CBS350 . I only found RAM and flash.Thank you for you help.SabrinaProduct Trials
Hi Guys, I have SX350X as my core switch and SG250X for access switch. SX350X is configured as a stack with a port channel configured with a trunk. This is also a same setup on my SG250X. I'm currently working for a GVRP configuration as the port cha...
Resolved! Dynamic routing in the SG switches stack
Will dynamic routing (RIP) work if I use 4 switches in a stack (2x SG550XG and 2x SG350X)?
Anybody can assist with the set-up reconfiguration of switch after installing new internet provider.
Hello, we have 3 550X-24FT 24-Port 10G Stackable Switches. We made them as a stack to provide us with some redundance in our Network. We just build the stack and were trying some things as we noticed that if we unplug the Stack Master the Standby Swi...
Hi, i was looking to enable some protected ports on CBS250 series, but the option has gone from the interface. even if i do a search, i only find protected lag. Firmware 3.1.1.7 Did i miss something or something has changed? The manual still has it ...
Hello, I'm about to buy 2 new CBS350-48p-4X, we already have one SG350X-48p.Is it possible to stack these two different Switchs ? Best regards
Hello,I have a couple of SG250X -24 port wit firmware 2.5.7.85, after a while the web interface is not more reachable through https protocol, I need to enable the http server via cli.I upgraded the firmware from 2.4.0.94 version to try to resolve thi...
I just purchased 4 CBS350-48P-4X switches. They are installed in two separate network cabinets about 30' apart, two on 1st floor and two on 2nd floor. All have 10GB SPF+ transceiver modules in the 10GB ports. All 10GB ports are configured as stack...
