Switches - Small Business

Hello Experts, I have just bought RV110W and installed it with Bell Hub2000 router, and I connect my RV110W WAN to Bell Hub 2000 LAN port 4, I have also put my RV110W in the DMZ with Bell Hub 2000 setting and I have 2 VLANs, VLAN1 is for WIFI (192.16...

I have two Catalyst 2960-X 48 GigE PoE 370W, 2 x 10G SFP+ LAN Base switches, I tried connect both switches with multimode fiber cable distance 150 meters with help of Transceiver SFP-10G-SR= now I am unable to connect both switches.

Dear Team,I have 17 small business switches model no. is SG-300-10 Mpp in my LAN  when I configure the Vlans at switch then i am not able to access the switch through telnet/remotely  because switch port do not remain the vlan-1 part I assigned the I...

Greetings,I have around 10 Small Business Switches from Cisco in my network (like SG550, SG350, ...)I do not have much experience with Cisco switching, VLANS and all those fancy things, and thus I always need external support in case of maintenance/e...

So I am having trouble accessing the web interface for my switch. I am in the command line and it shows as follows when I put in the command show ip interface:Gateway IP Address Activity status Type----------------------- ----------------------- ----...

Hi, Ive been checking Vlan - port relation in a few Cisco switches CiscoSG220/250/300/350/500. There is:dot1qVlanCurrentEgressPorts  "1.3.6.1.2.1.17.7.1.4.2.1.4.0"and another OIDdot1qVlanStaticEgressPorts = "1.3.6.1.2.1.17.7.1.4.3.1.2" In some models...

Just updated one of my SG300-10 from 1.4.10.6 to 1.4.11.2. Since then I cannot access the switch with the webbrowser via HTTPS anymore. Booting the other image with 1.4.10.6 via SSH resolves the issue. For now I will stay with 1.4.10.6 and will not u...

Can anyone advise above, my thought is the active ACL cannot be amend coz I am getting error, Cannot modify active list I am think I need to create a new 1 management profile with all the changes, make it active to replace the current 1. Am I correct...

Is it possible to have Cisco ISE filter out commands for users with TACACS+ Command Sets?  Is my only option to use the 3 privilege levels(1, 7, 15)?  

As a small business we use a number of the SG200-08, we use these all over the UK and France configured with a VPN and we do not use the POE, however, over the last few months we have had a number of the ports go down (no more than two on each device...

Hello,I've been monitoring the switch, there is something I do not understand.1.3.6.1.2.1.17.7.1.2.2.1.2.1.0.176.220.73.183.218 = Int32: 0 The bold is Vlan.The underlined is MAC. But the value is the port it is assigned to, and it's 0.How come it is ...

I have been testing all possible issues with this sg200-08p  I have 3 PoE cameras that are connected to the switch. Only ports 1&2 are up and are sending power to the cameras. I tested to see if the camera was the problem but when I plugged camera 3...

Dears,We are required to submit Warranty Certificate for SG350-28P-K9IN Switch purchased two months back.Without which Client is not willing to pay so it is CRUCIAL for us.I tried adding devices with my Cisco Partner Login but it simply shows "Not Co...

Hi I have a switch which is dismounted from production environment. What can I do to copy the current IOS image from flash to tftp server and upgrade the IOS and copy from TFTp server to the switch. Do I have have to fist delete the config to perform...