cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
279
Views
5
Helpful
2
Replies

Firmware Bug/damaged SG-350-10P

m00173
Beginner
Beginner

Hello, 

the firmware from my Cisco SG-350-10P-K9 V06 Switch is damaged.

 

When I send the firmware via X-modem, the download fails

What else can I do?

 

*******************************************************************

*** Running  SW  Ver. 2.5.5.47  Date May  6 2020  Time 17:25:42 ***

*******************************************************************

 

HW version is V06

Serial Number is PSZ24181CKX

Base Mac address is: 3c:57:31:d8:73:b7

Dram size is  : 512M bytes

Flash size is: 256M

06-May-2020 05:27:40 %CDB-I-LOADCONFIG: Loading running configuration.

06-May-2020 05:27:40 %CDB-I-LOADCONFIG: Loading startup configuration.

Device configuration:

Slot 1 - NSG350-10P

Device 0: CPSS_98DX3233 (AlleyCat3)

CPLD version is: 0x0e

CPU speed: 800 MHz

 

------------------------------------

-- Unit Factory Default           --

------------------------------------

 

06-May-2020 05:27:53 %INIT-I-InitCompleted: Initialization task is completed

-----------------------------------

-- Unit Number 1  Master Enabled --

-----------------------------------

 

06-May-2020 05:28:01 %MLDP-I-MASTER: Switching to the Master Mode.

06-May-2020 05:28:04 %SNMP-I-CDBITEMSNUM: Number of running configuration items                                                                                                                                                              loaded: 0

 

06-May-2020 05:28:04 %SNMP-I-CDBITEMSNUM: Number of startup configuration items                                                                                                                                                              loaded: 0

The SSH Server is generating a default RSA key.

This may take a few minutes, depending on the key size.

The SSH Server is generating a default DSA key.

This may take a few minutes, depending on the key size.

06-May-2020 05:28:05 %HAL_config_poe-F-POEInitError: HALP_config_poe_692xx_check                                                                                                                                                             _master_reset: HALP_config_poe_number_of_poe_devices is Zero. Failed on init.

 

***** FATAL ERROR *****

Reporting Task: HCPT.

Software Version: 2.5.5.47 (date May  6 2020 time 17:25:42)

base_address=0xb464d000

ros(+0x78dbc8)[0xb4ddabc8]

ros(HOSTG_fatal_error+0x10)[0xb4ddd47c]

ros(OSSYSG_fatal_error+0x2a0)[0xb53ae340]

ros(+0xb61f38)[0xb51aef38]

ros(HALP_config_poe_692xx_dev_op_set_periodic+0xa80)[0xb5768fb0]

ros(+0x110ca44)[0xb5759a44]

ros(HALP_config_poe_691xx_692xx_poe_dev_operation+0x3c)[0xb5759b24]

ros(HALC_config_poe_dev_operation+0x44)[0xb576c9ec]

ros(+0x10bd190)[0xb570a190]

ros(HALC_config_device_dispatch+0x1a8)[0xb570b110]

ros(+0x10da154)[0xb5727154]

ros(+0x10da364)[0xb5727364]

ros(+0x10da3ec)[0xb57273ec]

/lib/libp2linux.so.1(task_run+0xf4)[0xb45dd818]

 

***** END OF FATAL ERROR *****

 

**************************************************

*****************  SYSTEM RESET  *****************

**************************************************

Restarting system.

 

BootROM 1.41

Booting from NAND flash

General initialization - Version: 1.0.0

Serdes initialization - Version: 1.0.2

PEX: pexIdx 0, detected no link

DDR3 Training Sequence - Ver TIP-1.56.0

DDR3 Training Sequence - Switching XBAR Window to FastPath Window

Updated Physical Mem size is from 0x20000000 to 10000000

DDR3 Training Sequence - Ended Successfully

BootROM: Image checksum verification PASSED

 

 

ROS Booton: May 26 2019 14:16:26

 

Press x to choose XMODEM...

Booting from NAND flash

Running UBOOT...

U-Boot 2013.01 (May 06 2020 - 17:29:20) Marvell version: 2014_T3.0_eng_dropv6 2.                                                                                                                                                             5.5.1

Loading system/images/active-image ...

secure boot not supported

Uncompressing Linux... done, booting the kernel.

I2C frequency 100 kHz (Tclk 200 MHz, freq_m 12, freq_n 3)

 

MAC address   :  3c:57:31:d8:73:b7.

 

Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.

 

*******************************************************************

*** Running  SW  Ver. 2.5.5.47  Date May  6 2020  Time 17:25:42 ***

*******************************************************************

 

HW version is V06

Serial Number is PSZ24181CKX

Base Mac address is: 3c:57:31:d8:73:b7

Dram size is  : 512M bytes

Flash size is: 256M

06-May-2020 05:27:12 %CDB-I-LOADCONFIG: Loading running configuration.

06-May-2020 05:27:12 %CDB-I-LOADCONFIG: Loading startup configuration.

Device configuration:

Slot 1 - SG350-10P

Device 0: CPSS_98DX3233 (AlleyCat3)

CPLD version is: 0x0e

CPU speed: 800 MHz

 

------------------------------------

-- Unit Number 1                  --

------------------------------------

 

06-May-2020 05:27:25 %INIT-I-InitCompleted: Initialization task is completed

 

 

-----------------------------------

-- Unit Number 1  Master Enabled --

-----------------------------------

 

06-May-2020 05:27:34 %MLDP-I-MASTER: Switching to the Master Mode.

06-May-2020 05:27:35 %Entity-I-SEND-ENT-CONF-CHANGE-TRAP: entity configuration change trap.

06-May-2020 05:27:36 %SNMP-I-CDBITEMSNUM: Number of running configuration items loaded: 0

 

06-May-2020 05:27:36 %SNMP-I-CDBITEMSNUM: Number of startup configuration items loaded: 0

The SSH Server is generating a default RSA key.

This may take a few minutes, depending on the key size.

06-May-2020 05:27:37 %HAL_config_poe-F-POEInitError: HALP_config_poe_692xx_check_master_reset: HALP_config_poe_number_of_poe_devices is Zero. Failed on init.

 

***** FATAL ERROR *****

Reporting Task: HCPT.

Software Version: 2.5.5.47 (date May  6 2020 time 17:25:42)

base_address=0xb4726000

ros(+0x78dbc8)[0xb4eb3bc8]

ros(HOSTG_fatal_error+0x10)[0xb4eb647c]

ros(OSSYSG_fatal_error+0x2a0)[0xb5487340]

ros(+0xb61f38)[0xb5287f38]

ros(HALP_config_poe_692xx_dev_op_set_periodic+0xa80)[0xb5841fb0]

ros(+0x110ca44)[0xb5832a44]

ros(HALP_config_poe_691xx_692xx_poe_dev_operation+0x3c)[0xb5832b24]

ros(HALC_config_poe_dev_operation+0x44)[0xb58459ec]

ros(+0x10bd190)[0xb57e3190]

ros(HALC_config_device_dispatch+0x1a8)[0xb57e4110]

ros(+0x10da154)[0xb5800154]

ros(+0x10da364)[0xb5800364]

ros(+0x10da3ec)[0xb58003ec]

/lib/libp2linux.so.1(task_run+0xf4)[0xb46b6818]

 

***** END OF FATAL ERROR *****

 

**************************************************

*****************  SYSTEM RESET  *****************

**************************************************

Restarting system.

 

BootROM 1.41

Booting from NAND flash

 

 

General initialization - Version: 1.0.0

Serdes initialization - Version: 1.0.2

PEX: pexIdx 0, detected no link

DDR3 Training Sequence - Ver TIP-1.56.0

DDR3 Training Sequence - Switching XBAR Window to FastPath Window

Updated Physical Mem size is from 0x20000000 to 10000000

DDR3 Training Sequence - Ended Successfully

BootROM: Image checksum verification PASSED

 

 

ROS Booton: May 26 2019 14:16:26

 

Press x to choose XMODEM...

Booting from NAND flash

 

Running UBOOT...

 

 

U-Boot 2013.01 (May 06 2020 - 17:29:20) Marvell version: 2014_T3.0_eng_dropv6 2.5.5.1

 

Loading system/images/active-image ...

secure boot not supported

Uncompressing Linux... done, booting the kernel.

I2C frequency 100 kHz (Tclk 200 MHz, freq_m 12, freq_n 3)

 

 

MAC address   :  3c:57:31:d8:73:b7.

 

Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.

 

*******************************************************************

*** Running  SW  Ver. 2.5.5.47  Date May  6 2020  Time 17:25:42 ***

*******************************************************************

 

HW version is V06

Serial Number is PSZ24181CKX

Base Mac address is: 3c:57:31:d8:73:b7

Dram size is  : 512M bytes

Flash size is: 256M

06-May-2020 05:27:12 %CDB-I-LOADCONFIG: Loading running configuration.

06-May-2020 05:27:12 %CDB-I-LOADCONFIG: Loading startup configuration.

Device configuration:

Slot 1 - SG350-10P

Device 0: CPSS_98DX3233 (AlleyCat3)

CPLD version is: 0x0e

CPU speed: 800 MHz

 

 

1 Accepted Solution

Accepted Solutions

marce1000
VIP Mentor VIP Mentor
VIP Mentor

 

    - FYIhttps://bst.cloudapps.cisco.com/bugsearch/bug/CSCvk62334  , 'workaround' mentioned in the bug report is RMA

 M.

View solution in original post

2 Replies 2

balaji.bandi
VIP Community Legend VIP Community Legend
VIP Community Legend

If you are not able to install firmware using xterm, then you need to raise a TAC case for replacemet.

 

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

marce1000
VIP Mentor VIP Mentor
VIP Mentor

 

    - FYIhttps://bst.cloudapps.cisco.com/bugsearch/bug/CSCvk62334  , 'workaround' mentioned in the bug report is RMA

 M.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Recognize Your Peers