04-15-2020 05:45 AM - edited 04-15-2020 05:45 AM
all ports in specs must support 10G but i have some port i can't make 10G either from web or CLI and from CLI when executing command it shows Port can not be configured to speed 10G
Thanks
Solved! Go to Solution.
04-19-2020 02:53 AM
Hi again Abdalnoor,
That is why you cannot go to 10gigabit - your SFP (SFP-1000-LX) is a gigabit one.
Try to replace it with 10gigabit - as per datasheet:
SKU | Media | Speed | Maximum distance |
SFP-H10GB-CU1M= | Copper coax | 10 Gbps | 1 m |
SFP-H10GB-CU3M= | Copper coax | 10 Gbps | 3 m |
SFP-H10GB-CU5M= | Copper coax | 10 Gbps | 5 m |
SFP-10G-SR= | Multimode fiber | 10 Gbps | 26 m to 400 m |
SFP-10G-LR= | Single-mode fiber | 10 Gbps | 10 km |
SFP-10G-SR-S= | Multimode fiber | 10 Gbps | 26 m to 400 m |
SFP-10G-LR-S= | Single-mode fiber | 10 Gbps | 10 km |
Hope it helps
Regards,
Mike
04-15-2020 08:37 AM
- So , what happens then or what kind of error are you getting when you try this ?
M.
04-15-2020 09:22 AM
04-16-2020 01:37 AM
- Check if this article can help you :
M.
04-16-2020 06:16 AM
04-16-2020 10:22 AM
- Try using latest firmware for your device anyway if not yet done, then have a drive-through test by connecting a 10-Gb SFP+ with a connection, sometimes speeds get auto-configured. Check if the device reacts 'wisely' if get's a 10 Gb connection to handle.
M.
04-18-2020 10:19 PM
Hello Abdalnoor,
what shows the following command:
switch# show inventory teX/0/X
where X is the port number in question
04-19-2020 01:39 AM
PID: SFP-1000-LX VID: Information Unavailable
04-19-2020 02:53 AM
Hi again Abdalnoor,
That is why you cannot go to 10gigabit - your SFP (SFP-1000-LX) is a gigabit one.
Try to replace it with 10gigabit - as per datasheet:
SKU | Media | Speed | Maximum distance |
SFP-H10GB-CU1M= | Copper coax | 10 Gbps | 1 m |
SFP-H10GB-CU3M= | Copper coax | 10 Gbps | 3 m |
SFP-H10GB-CU5M= | Copper coax | 10 Gbps | 5 m |
SFP-10G-SR= | Multimode fiber | 10 Gbps | 26 m to 400 m |
SFP-10G-LR= | Single-mode fiber | 10 Gbps | 10 km |
SFP-10G-SR-S= | Multimode fiber | 10 Gbps | 26 m to 400 m |
SFP-10G-LR-S= | Single-mode fiber | 10 Gbps | 10 km |
Hope it helps
Regards,
Mike
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: