06-08-2013 04:17 PM
I'm having some trouble with creating a vlan trunk between an SG300-52 and a Cisco Catalyst 3560G. I have 4 VLANS (1, 2, 10, and 11) on the 3650 and I need ports on the SG300 to be able to communicate with them.
On the 3560, port 14 is set to:
interface GigabitEthernet0/14
switchport trunk encapsulation dot1q
switchport mode trunk
spanning-tree portfast
On the Sg300, port 52 is set to:
interface GigabitEthernet52
spanningtree link-type point-to-point
switchport trunk allowed vlan add 1,2,10,11
macro description switch
Trying to figure out what's wrong... Any help would be appreciated.
Thanks,
Chris
Solved! Go to Solution.
06-08-2013 07:09 PM
Hi Chris, the first problem is the spanning-tree portfast, it shouldn't be on a switch interconnect. You may have a native vlan mismatch as well but that shouldn't matter.
One suggestion though, set the SG300 port to general mode and disable the ingress filter.
-Tom
Please mark answered for helpful posts
06-08-2013 07:09 PM
Hi Chris, the first problem is the spanning-tree portfast, it shouldn't be on a switch interconnect. You may have a native vlan mismatch as well but that shouldn't matter.
One suggestion though, set the SG300 port to general mode and disable the ingress filter.
-Tom
Please mark answered for helpful posts
06-08-2013 08:29 PM
Hi Tom,
I made the changes, but still no go. I lose ping to the SG300 as soon as I remove the "switchport access vlan 11" line on the catalyst switch.
Catalyst: (10.10.2.199)
interface GigabitEthernet0/14
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1,2,10,11
switchport mode trunk
SG300: (10.10.11.90)
interface gigabitethernet48
switchport mode general
switchport general allowed vlan add 2,10-11 tagged
switchport general ingress-filtering disable
02-17-2017 06:00 PM
Is the scripting command set the same for both the 3560 and the SG300?
06-10-2013 09:10 AM
Okay, I figured out what it was. On the catalyst, you need to include the default vlan in the vlan list. The SG series seems to ignore native vlan when coming from a catalyst. I've highlighted the change below. Here's the configuration that is confirmed as working:
SG 300:
interface gigabitethernet52
spanning-tree link-type point-to-point
switchport mode general
switchport general allowed vlan add 2,10-11 tagged
macro description switch
Catalyst:
interface GigabitEthernet0/52
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1,2,10,11
switchport mode trunk
For others with vlan troubles:
On the SG300, if you want a port to be on a particular VLAN, set the Mode to Access then add the vlan id to the port as untagged and PVID. For example, if you want a workstation to be on VLAN 11, it will show up as "11UP" in the Port VLAN Membership screen.
08-08-2013 08:20 AM
it works fine for me too. many thanks!!
10-14-2013 12:44 AM
can we setup like vlan 11 as the managment vlan and defalt vlan ?
thank you
09-04-2021 10:47 AM
Hi, I am having the same issue, with the below scenario.
Switch 1 (SG350X)
Switch 2 (3560G) 1
Switch 3 (2960S)
With 6 Vlans
All 3 Switches connected through trunk port.
Switch 1 --> Switch 2 --> Switch 3
Problem is I am not able to communicate from PC connected to Switch 3 to PC Connected to Switch 1.
I tried the configuration as above but no luck, Please help, what can be the issue.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide