06-02-2018 03:20 AM - edited 03-21-2019 11:25 AM
Hi,
I have an SG 350-X stack ( of two switches ) which is connected to a Juniper switch with 6 cables in a LAG group. From the Juniper switch I can see that the LAG speed is 6 Gig, but from the Cisco side I see only I Gig. Is there any way I can make sure that the LAG on Cisco side is operating at 6G or 1G ? . I did not enable LACP on both sides. The screen shot from Cisco is attached.
Thanks
06-03-2018 07:02 AM
Hi,
My name is Iliya Gatsev from Cisco Technical Support Team.
Are you using SFP or RJ-45 ports on the Cisco switches ? Could you share screen shot from the LAG Management page of the Cisco and from the Juniper if you don't mind ?
Iliya Gatsev
Cisco STAC Network Engineer
Together we are the human network .:|:.:|:. CISCO
06-03-2018 09:22 AM
06-05-2018 06:48 AM
Hello Mohammed,
Can you issue the command in CLI (console or SSH):
switchxxxxxx# show interfaces status
and paste here the output
06-05-2018 09:02 AM
Hi Mipopov;
please find below :
PFQ-USER-SW#show interfaces status
Flow Link Back Mdix
Port Type Duplex Speed Neg ctrl State Pressure Mode
-------- ------------ ------ ----- -------- ---- ----------- -------- -------
gi1/0/1 1G-Copper -- -- -- -- Down -- --
gi1/0/2 1G-Copper -- -- -- -- Down -- --
gi1/0/3 1G-Copper -- -- -- -- Down -- --
gi1/0/4 1G-Copper -- -- -- -- Down -- --
gi1/0/5 1G-Copper -- -- -- -- Down -- --
gi1/0/6 1G-Copper -- -- -- -- Down -- --
gi1/0/7 1G-Copper -- -- -- -- Down -- --
gi1/0/8 1G-Copper -- -- -- -- Down -- --
gi1/0/9 1G-Copper -- -- -- -- Down -- --
gi1/0/10 1G-Copper -- -- -- -- Down -- --
gi1/0/11 1G-Copper -- -- -- -- Down -- --
gi1/0/12 1G-Copper -- -- -- -- Down -- --
gi1/0/13 1G-Copper -- -- -- -- Down -- --
gi1/0/14 1G-Copper -- -- -- -- Down -- --
gi1/0/15 1G-Copper -- -- -- -- Down -- --
gi1/0/16 1G-Copper -- -- -- -- Down -- --
gi1/0/17 1G-Copper -- -- -- -- Down -- --
gi1/0/18 1G-Copper -- -- -- -- Down -- --
gi1/0/19 1G-Copper -- -- -- -- Down -- --
gi1/0/20 1G-Copper -- -- -- -- Down -- --
gi1/0/21 1G-Copper -- -- -- -- Down -- --
gi1/0/22 1G-Copper -- -- -- -- Down -- --
gi1/0/23 1G-Copper -- -- -- -- Down -- --
gi1/0/24 1G-Copper -- -- -- -- Down -- --
gi1/0/25 1G-Copper Full 1000 Enabled Off Up Disabled Off
gi1/0/26 1G-Copper Full 1000 Enabled Off Up Disabled Off
gi1/0/27 1G-Copper Full 1000 Enabled Off Up Disabled On
gi1/0/28 1G-Copper -- -- -- -- Down -- --
gi1/0/29 1G-Copper Full 100 Enabled Off Up Disabled Off
gi1/0/30 1G-Copper Full 10 Enabled Off Up Disabled On
gi1/0/31 1G-Copper -- -- -- -- Down -- --
gi1/0/32 1G-Copper Full 10 Enabled Off Up Disabled On
gi1/0/33 1G-Copper Full 1000 Enabled Off Up Disabled Off
gi1/0/34 1G-Copper Full 10 Enabled Off Up Disabled Off
gi1/0/35 1G-Copper -- -- -- -- Down -- --
gi1/0/36 1G-Copper -- -- -- -- Down -- --
gi1/0/37 1G-Copper -- -- -- -- Down -- --
gi1/0/38 1G-Copper -- -- -- -- Down -- --
gi1/0/39 1G-Copper -- -- -- -- Down -- --
gi1/0/40 1G-Copper -- -- -- -- Down -- --
gi1/0/41 1G-Copper -- -- -- -- Down -- --
gi1/0/42 1G-Copper -- -- -- -- Down -- --
gi1/0/43 1G-Copper -- -- -- -- Down -- --
gi1/0/44 1G-Copper -- -- -- -- Down -- --
gi1/0/45 1G-Copper -- -- -- -- Down -- --
gi1/0/46 1G-Copper Full 1000 Enabled Off Up Disabled Off
gi1/0/47 1G-Copper Full 1000 Enabled Off Up Disabled On
gi1/0/48 1G-Copper Full 1000 Enabled Off Up Disabled Off
te1/0/1 10G-Combo-C -- -- -- -- Down -- --
te1/0/2 10G-Combo-C -- -- -- -- Down -- --
gi2/0/1 1G-Copper Full 10 Enabled Off Up Disabled Off
gi2/0/2 1G-Copper Full 1000 Enabled Off Up Disabled Off
gi2/0/3 1G-Copper -- -- -- -- Down -- --
gi2/0/4 1G-Copper Full 10 Enabled Off Up Disabled On
gi2/0/5 1G-Copper Full 100 Enabled Off Up Disabled On
gi2/0/6 1G-Copper Full 10 Enabled Off Up Disabled Off
gi2/0/7 1G-Copper -- -- -- -- Down -- --
gi2/0/8 1G-Copper Full 10 Enabled Off Up Disabled Off
gi2/0/9 1G-Copper Full 1000 Enabled Off Up Disabled On
gi2/0/10 1G-Copper -- -- -- -- Down -- --
gi2/0/11 1G-Copper -- -- -- -- Down -- --
gi2/0/12 1G-Copper Full 10 Enabled Off Up Disabled On
gi2/0/13 1G-Copper Full 10 Enabled Off Up Disabled Off
gi2/0/14 1G-Copper Full 10 Enabled Off Up Disabled On
gi2/0/15 1G-Copper -- -- -- -- Down -- --
gi2/0/16 1G-Copper Full 1000 Enabled Off Up Disabled Off
gi2/0/17 1G-Copper Full 10 Enabled Off Up Disabled Off
gi2/0/18 1G-Copper Full 10 Enabled Off Up Disabled On
gi2/0/19 1G-Copper Full 10 Enabled Off Up Disabled Off
gi2/0/20 1G-Copper Full 10 Enabled Off Up Disabled Off
gi2/0/21 1G-Copper Full 10 Enabled Off Up Disabled On
gi2/0/22 1G-Copper Full 10 Enabled Off Up Disabled Off
gi2/0/23 1G-Copper -- -- -- -- Down -- --
gi2/0/24 1G-Copper -- -- -- -- Down -- --
gi2/0/25 1G-Copper -- -- -- -- Down -- --
gi2/0/26 1G-Copper -- -- -- -- Down -- --
gi2/0/27 1G-Copper -- -- -- -- Down -- --
gi2/0/28 1G-Copper -- -- -- -- Down -- --
gi2/0/29 1G-Copper -- -- -- -- Down -- --
gi2/0/30 1G-Copper -- -- -- -- Down -- --
gi2/0/31 1G-Copper -- -- -- -- Down -- --
gi2/0/32 1G-Copper -- -- -- -- Down -- --
gi2/0/33 1G-Copper -- -- -- -- Down -- --
gi2/0/34 1G-Copper -- -- -- -- Down -- --
gi2/0/35 1G-Copper -- -- -- -- Down -- --
gi2/0/36 1G-Copper -- -- -- -- Down -- --
gi2/0/37 1G-Copper -- -- -- -- Down -- --
gi2/0/38 1G-Copper -- -- -- -- Down -- --
gi2/0/39 1G-Copper -- -- -- -- Down -- --
gi2/0/40 1G-Copper -- -- -- -- Down -- --
gi2/0/41 1G-Copper -- -- -- -- Down -- --
gi2/0/42 1G-Copper -- -- -- -- Down -- --
gi2/0/43 1G-Copper -- -- -- -- Down -- --
gi2/0/44 1G-Copper -- -- -- -- Down -- --
gi2/0/45 1G-Copper -- -- -- -- Down -- --
gi2/0/46 1G-Copper Full 1000 Enabled Off Up Disabled On
gi2/0/47 1G-Copper Full 1000 Enabled Off Up Disabled Off
gi2/0/48 1G-Copper Full 1000 Enabled Off Up Disabled Off
te2/0/1 10G-Combo-C -- -- -- -- Down -- --
te2/0/2 10G-Combo-C -- -- -- -- Down -- --
Flow Link
Ch Type Duplex Speed Neg control State
-------- ------- ------ ----- -------- ------- -----------
Po1 1G Full 1000 Enabled Off Up
Po2 -- -- -- -- -- Not Present
Po3 -- -- -- -- -- Not Present
Po4 -- -- -- -- -- Not Present
Po5 -- -- -- -- -- Not Present
Po6 -- -- -- -- -- Not Present
Po7 -- -- -- -- -- Not Present
Po8 -- -- -- -- -- Not Present
PFQ-USER-SW#
06-17-2020 11:20 AM
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: