SFP CISCO-AVAGO SFCT-5798PZ-CS3

[Abdel Tobbal]

Hi,

Is sfp CISCO-AVAGO SFCT-5798PZ-CS3 (it's 1 GE sfp) supported on Storage Node (SSN16) module on Cisco MDS9513 switch Director ?

If yes, short wave fc cable connexion or lon wave fc cable connexion ? 

thanks

Abd

[Vu Phan]

Hello Abdel,

The below are SFPs you can use for SSN-16 line card

DS-SFP-FCGE-SW	Cisco MDS 9000 Family Gigabit Ethernet, 1/2-Gbps Fibre Channel-Shortwave, SFP, LC
DS-SFP-FCGE-LW	Cisco MDS 9000 Family Gigabit Ethernet, 1/2-Gbps Fibre Channel-Longwave, SFP, LC
DS-SFP-GE-T	Gigabit Ethernet Copper SFP, RJ-45

Thanks

[24madaeve1]

Hi Vu Phan

I have an issue in my data center, could you please me help out.

I have Cisco ASR1006 router in my data center and a 100Mpbs WAN link (over OFC) is coming from my ISP to my premises. The issue is my ISP is having 100BaseFx module at its end and I am having 1000BaseFx modules in my router. How should I terminate the OFC on my router as 100BaseFx are 1000BaseFx are incompatible ? Please recommend any SFP which I could use at my end in order to terminate the OFC directly on my router. 

[Leo Laohoo]

I have already responded to your THREAD.

[Abdel Tobbal]

Hi Vu,

thanks so much for your answer. I'd like to give you more details on my problem. The cisco sfp avago is already pluged on the SSN16 module for 2 or 3 years ago but not used. We used only Copper sfp's for fcip distant connexions (connexions to Nexus). But now we have a new migration projet and we need GE FC connexion to Cisco ASR 1002-F which is connected to Colt DWDM.

Here is an exeample of the copper sfp we use and working very well.  How to know if it's a DS-SFP-GE-T ??

MDS1COREDIDPA#  sho int gigabitethernet 9/9 transceiver details
GigabitEthernet9/9 sfp is present
    Name is CISCO-METHODE
    Manufacturer's part number is SP7041-SBU
    Revision is E
    Serial number is MTC1446012Z
    Cisco part number is
    Cisco pid is
    Nominal bit rate is 1300 Mb/s
    Cisco extended id is unknown (0x0)

    No tx fault, no rx loss, in sync state, diagnostic monitoring type is 0x0
    Digital diagnostics feature not supported in SFP

Here is the sfp GE FC pluged we want to use. How to know if it's a DS-SFP-FCGE ??

MDS1COREDIDPA#  sho int gigabitethernet 9/1 transceiver details
GigabitEthernet9/1 sfp is present
    Name is CISCO-AVAGO
    Manufacturer's part number is SFCT-5798PZ-CS3
    Revision is 0000
    Serial number is AGC1521ULFF
    Cisco part number is
    Cisco pid is
    Nominal bit rate is 1200 Mb/s
    Link length supported for 9/125mm fiber is 10.100 km
    Link length supported for 50/125mm fiber is 550 m
    Link length supported for 62.5/125mm fiber is 550 m
    Cisco extended id is unknown (0x0)

    No tx fault, no rx loss, in sync state, diagnostic monitoring type is 0x0
    Digital diagnostics feature not supported in SFP

Regards,

Abd