Update: This portion of the project has finished earlier than initial projections. We are approaching our latest step in relabelling posts across the Small Business board. 1 week from today, read-only mode will be active on this discussion board fro...
Forum Posts
Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Catalyst 1200 & 1300 Hardware Installation Guide - Catalyst 1300 Hardware Installation Guide - Catalyst ...
We are using two SG500-52 switches in a stack, in L3 system mode and with the latest firmware 1.4.1.03.The stack of switches is connected with 2-port LAGs to ESXi hosts. One port of the LAG is on Master switch, the other one is on Backup switch.LAGs ...
Resolved! Fan speed on SF200-24p full POE
Hello, i'm surpised by the high speed fan on this model by default. Can i reduce the fan speed or activate a better fan modulation? Thanks (Total PoE Power Consumption : 43W)
Resolved! SG500X-48MP stacked voip vlan issue
Ok. I have one for you. Everything is working at the moment but not working how I thought it would. I have a SG300-52MP that I configured first. Smartport, dynamic voice vlan disabled, LLDP, CDP enabled as default. vlans are 1,10,20,30,40,50,60,70,...
Hi, all! The main reason why I'm open the topic - can't connect to switch, I don't know its IP and I can't find it, despite I'm connected directly to ethernet port. I tried to find IP by LanScope or WireShark. Also, I tried to connect by standart C...
Hello, I would like to know if there is a possibility to achieve similar behavior like on IOS devices. If the user is not found in the local database, then radius is used. This works on IOS devices (tested on ASR920 and ME3400), but not on SMB switch...
We are trying to find a way to log issued DHCP leases. With the Catalyst series switches we can do this by enabling debugging of DHCP to syslog, and then using event management to force this to persist reload (not ideal but there doesn't seem to be...
Hi, I am using PFsense as a router & setup a vlan 50 - i am looking to put 3 WAPS on Vlan 50 - to keep my kids off my work computers network. I setup the Pfsense Vlan I followed a youtube video. End result is having PFsense give an Ip for Vlan 50 o...
I am trying to enable SSH in my SG300 (latest firmware). I’ve got the service running, but when I attempt to connect from macOS 10.13 or Windows 10 (power shell) I get a message like this “no matching cipher fo und: client 3des-cbc,aes128-cbc,aes192-...
Hi everyone, I'm having problems trying to configure this, it's the most simple setup I have no idea why I can't get this going. There seems to be a lot of posts similair but nothing that explained the fix that worked for me. I have an ADSL router wh...
Resolved! native vlan access port
hi, in sg500 default all ports in native vlan are trunk. i have configured 2 vlans and set all ports as access. To connect switch with second switch i need one trunk port . Should i change all other ports to access in native vlan ? Do you create a l...
Due to a lightning strike, my old SG300-28 switch had to be replaced. I decided to go for a SG350-28 as a replacement, which I now regret. It seems near impossible to transfer the configuration. I soon realised that I couldn't just upload the confi...
I have two SG300-28P (SRW2024P) switches and one seems to be dead. When plugged in, the fans turn on, the power comes on, and the port LEDs light for a split second just like it is supposed to do. But, there is no console response and one, sometime...
Hello All, I need to know which SFP+ modules fit into the SG350XG-24F-K9 and other Small Business Switches? Is there a compatibility matrix available? KR Walter
Resolved! SG350 TCAM max ressource
I worked as an IT Admin in a school and we have to renew our L3 switches. I have used previously in some little sites SG300-52 or 28 and i know the TCAM ressources are limited (around 500 entries if i remember). I'v difficulties to find these val...
As per the documentation Cisco switch model SG350X-48P has 4 x 10 Gigabit Ethernet fiber uplinks. Can we use the 1 Gig fiber SFPs in these 10 Gig fiber uplink slots? We have a requirement where we need to use this model and connect it to uplink switc...