Switches - Small Business

Hello, I have a switch SG200-26 26 port, it work, have firmware 1.4.7.6. some port work normally - is UP, bat for example port 12,24,11,23 if is connected server NAS QNAP 412 P || status port is Down , no UP, I haven't connection, if I connect other ...

I have a SG300-28 in L3 mode feeding a SG200-08 which is working.  I decided to upgrade to a SG500X-24 switch so I could play with a routing protocol.  I have a trunk port between the SG500X-24 switch and the SG200-08 switch.  For some reason VLAN2 d...

Hey, "Join VLAN" in "Port VLAN Membership" seems completely broken. First, it does not even show the initially selected port (here I selected GE28 and it shows GE1). Even when I change it manually in the popup, it does not show any mode or available ...

Hi, i use SF220-48 48-Port 10/100 Smart Plus Switch and acquiring network address 40 seconds after plugged in LAN cable. All settings are applied by default. Also have two SF200-48 and acquiring network address immediately. Can someone help me ?

We are retiring some old SGE2000s and replacing with an SG500-52P.  We'd like to physically  mount is in the middle of the current SG500 Stack.  our current physical layout is... SW1 -->  SW2 --> SW3 --> SW1 We'd like to change it to: SW1 --> SW4 ...

Hello, I'm stuck with this scenario, I have read a lot of information on Internet but it doesn't work: I need to configure a second SSID only for guest access, isolated from LAN data: 2x Access Point Linksys LAPAC1750PRO Switch Cisco SG200-50p Route...

Hello all I am having problem in configuring Cisco SG300-10PP-K9 with hyperterminal. I am a beginner in thede things. So kindly help me in doing so

We have an SG300-28P that is part of a vendor provided equipment stack in support of an elaborate audio and video system in a conference suite. I have read online here that ports 1-24 are POE, yet when I connect a Cisco CP 8961 phone into any one of ...

I got my hands on an SG500-28 switch which I have setup in L3 mode.  The problem is a cannot change the IP for VLAN1.  It will not let me delete it and setup another VLAN1 nor can I change the IP under edit using the GUI.  I wonder if it has somethin...

Hi Team, WE have purchased SG500x small business model switch, In that user module there is support for VRRP and we configured the IP.But we are facing the issue of VRRP ip of configured switch ICMP is not working. Please help on this case for any ...

I have no working knowledge of using a managed switch and looking for some guidance. Scenario: I have a Dell C6100 (2U server with 4 nodes).  Each node has it's own Public IP address and I have the server in a Data Center (co-location).  The patch pa...

Greetings, A port scan on our SG500-52P recently discovered that on SSH Port 22 the version information of SSH was advertised. Specifically, if you run the following nmap command: nmap -sV -p 22 -Pn --script banner X.X.X.X You recieve the following ...

Hello!! i a facing a certain problem and i would be grateful if someone could help me. as show in the network photo, my main switch is the dhcp server. i have many vlans configured on my network. the problem is that i created a new vlan for the voip...

I configured 802.1x on a sg300 switch. It is working very well with some Windows 7 machines and a Windows Server 2008 NPS server.Now I tried to get the MAC authentication running, on a 3850X it is working without problems, but every access request se...

Hello, One of our SG300-28 switches stopped reporting any data for SFP transceivers (GLC-SX-MMD) in gi28:   gi27       57    3.33    2.39    0.28    0.28   No    gi28       0      0.0     0.0    1.00    1.00   No Swapping the transceivers or rep...