Switches - Small Business

Hi I'm having trouble getting SNMPWalk to get the OIDs from one of my Cisco SG500X switches. I thought I'll download the latest MIB zip file and apply it - but how do I install the MIB? thanks

Hi, I have setup a SG300 (in L3 mode) as below but can't solve what I thought should be a simple problem, but cannot for the life of me figure it out. PC1 and PC2 can ping each other and 192.168.1.100 (port GE1). So I'm happy that VLAN setup and DHCP...

problems connecting an access point to a switchmy connection is as shown in the topology.equipment used-> An access point Cisco Aironet 2600i IOS made a change to a system of autonomous version, IOS is currently installed ap3g2-k9w7-tar.153-3.JAB,.->...

こんにちは。SG300-20JPを6台所有しています。 fw-1.4.5.02、boot-1.3.5.06 で統一しています。 うち1台だけ Green Ethernet > プロパティ の画面で 802.3 Energy Effcient Ethernet (EEE) のチェックボックスが存在しません。 試しにCUIで接続し、#show eeeと打ち込んでも Unrecognized command と返されます。 Green Ethernet > ポート設定では、ポート設定の編集ポップアッ...

hi, i recommended a Cisco switch for my workplace because i learnt it was the best. they finally brought in SF 100-24 (small business) switch. but the problem is that i cant seem to configure and work with it at all. when i connect the computers thro...

(Before anyone says anything , yes, I know SNMP is not an advertised feature of the SLM2008, but where's the fun in that?) So does anyone know how to edit the switch.cfg file generated by the device when you go to save the configuration? (No, its not...

Hello, So, I just got a SF300 switch for our small business. I am trying to configure it but i am a little confused. I have set the switch to layer 3 mode and accessed it through the CLI. I have created a new VLAN and assigned it all 24 Fa ports, I ...

Hi All, we successfully stacked 4 SG500 in ring topology with this cable SFP-H10GB-CU1M. Now we need to connect the stack to an existing SG500x with a normal data uplink (not stack). Is the cable SFP-H10GB-CU3M suitable to realize this connection? W...

Hi All, I've am not that advance level user of Cisco WLC but I have recently deployed (Dynamic VLAN) wired network security with cisco switches. The same I need to configure with Cisco WLC 2504 using the existing VLANs created in my network.  Scenar...

Hi Team, I have Cisco SG300-52 52 Port Managed Switch. Does the switch support Inter-VLAN Routing with the help of a Layer 3 Device? If yes, please help me with the configuration. Regards, Sri Charan M S

Hi,I have upgraded my SG200-08 switches from firmware version 1.0.5.1 to version 1.0.6.2. Since that new firmware is active, the network-printing from my Macbooks and iMacs is not working anymore. They all have TCP/IP connected network printers (not ...

Hello, We have 3 switchs SG500-52 and i would know what is the maximum speed we can have for stacking mode. PS : Enclosed the actual configuration of our stack. Is this the optimal speed ? Thank you for your answers. David ROSSI

Hola¡ Estoy configurando un SG500 y no consigo que los equipos de las diferentes subredes hagan ping al router, por lo tanto no tienen internet. Pego la configuracion a ver si me podeis echar una mano, muchas gracias¡¡¡¡¡ config-file-headerSG500v1...

I just bought a new SGE2000P switch.  In trying to do the configuration for use, I have logged in using the serial interface, set the IPV4 information and saved it.  I then try to connect using the web interface.  I get the welcome screen, login in u...