Switches - Small Business

We have 2(two) SG300-28 switches. We have several VLANS that need to be truked between switch A and switch B 1. We are able to create 1 TRUNK port  that includs vlan 2,3,4 and it works fine between switch A and B.  We are now trying to create a 2nd T...

Hello!  I have 5 of SG500X-24 PORT GIGABIT WITH 4-PORT 10-GIGABIT STACKABLE MANAGED SWITCH that i have recently started managing.  Recently, those switches have been acting up and makes our drive go down with internet connection for some of our users...

Hi guys, So here's the setup: 2 switches: Switch1 3560x Switch2 3560x (10gbe c3kx-nm-10g module) 3 vlans: 1(default) 200 (storage) 201 (vmotion) poweredge servers: a blade m1000e chassis with 10gbe pass through module esxi for ose on the blades. ...

Anyone have an opinion on this?Setup:An sg300-10 configured in L3 mode.There are 4 vlans defined (with 4 IPv4 addresses, though the sg300 is not routing -- other device does).In IPv4 all works fine.Trying to add IPv6 to my network I found out that:- ...

I have a couple of SG300 28 port switches that I just purchased over the last few months, we changed out our phone system so we using voice over IP phones and the phones are now connected to our pc's.  For some reason, the ports are dropping on the s...

I have a cisco sg500-52 port running in a stack config with another cisco sg500. I cannot get console access into the box. i have tried turning off the secondary switch and trying to console into the master. i have tried multiple different baud rates...

I've forgotten username & password of SG300-28 28-Port Gigabit Managed Switch. Is there any to recover them? but I don't want to lose configurations. 

I'm using a SG300-28MP switch (firmware updated to the latest version): and when I make a connection to an Axis M3014 POE ip camera, nothing happens. The camera doesn't boot up and it seems it doesn't get any power through POE. When I use the camer...

Hi All, I have a sg 300 running multiple VLans. One Vlan, 223 is for BACNet BMS, 3 ports are assigned to this VLan, 1 for the BMS Admin, 1 for connection to the rest of the BMS Lan and 1 for a Crestron Processor, which interogates the BACNet and feed...

Hello i need to configure zabbix for receive statistics from SPS224G4. but i cannot find any zabbix template. Can you help me with this? Also i read this topic - https://supportforums.cisco.com/discussion/10851326/how-enable-lldp-sps224g4-switch  and...

We have a variety of these switches deployed as well as the 50 port model. After upgrading to version 1.0.0.19 the thermal thresholds had a massive jump from 50 Celcius range to the 90 Celcius range. This is obviously something that couldn't go unnot...

Hello, I come here in despair. I tried so much things that i don't know anymore how to do it. Here the situation : I have a DHCP which is on the management vlan (vlan 10 - 192.168.1.11/26) I have multiples switches in L3 mode having an ip in the Vl...

Hello I have a Cisco Switch 2960-X Series which is not working completely and is showing these error : Err: Interrupt: Machine check (0x200): Data access error:     PC: 0x1f19e5e8, MSR: 0x00021000, ESR: 0x00000000, MCSR: 0x82000000 (Bailed out.) ca...

SG220-26 (on latest 1.0.0.19 firmware) is logging "Oversize Packets" errors at alarming rate from any trunked ports. These show up in RMON and EtherLike statistics. It seems as if switch is (incorrectly) logging 802.1q tagged frames "oversize" when ...