Switches - Small Business - Page 237

Looking for support docs and videos? Check here

We recently announced the release of our self-serve virtual assistant. You can read the full announcement here. Videos and documents are available within a click for our latest products. Once you've told the bot what device you're using, the context ...

Helpful support links - Updated September 2023 w/ Catalyst 1200 - 1300

(Updated September 2023 - Added Catalyst 1200 and Catalyst 1300 ) Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Catalyst 1200 & 1300 Hardware Install...

Resolved! SG300-10 - DHCP Server did not update DNS (bind9) records

Hi Community, my SG300 is configured in L3 Mode in my Homelab and the DHCP Server feature is enabled. The switch is running on Firmware Version 1.4.1.3. I've configured per VLAN one Network Pool. The Default Router IP Address (Option 3), the DNS Serv...

Environmental Protection issue for CISCO-SG300-10 10 port Gigabit managed Switch

I have been calling 800903154 & 852-30775555. But neither party could help. Actually, we have been buying CISCO-SG300-10 10-port Gigabit Managed Switch locally in HKG. And we have our end customer asking something about environmental protection n abo...

SG220 50P - Various issues (port breaks - uplinks strange - webinterface random security)

Hi, I have various issues with my 3 switches. Switch 1 ====>connected on stp to core switch on port 49 (trunk and uplink enabled) Connected on stp to switch 2 on port 50 (trunk and uplink enabled)Issue switch 1: Connection r...

Port problem Cisco SG100D

I have a question about the SG100D switches series. My network is as following.It starts with a Glasfiber modem --> Draytek Vigor modem. In the modem I have plugged in 3 Cisco SG100D switches, two of them with 5 ports and one of them with 8 ports.One...

Reset switch replacement

I have a Cisco SG300-28P Managed Switch. After repeated attempts to reset the unit, I discovered that the reset switch had broken. There were two small pieces that appear to be an internal piece (the part that shorts the pins) and what appears to b...

Resolved: Can't Factory Reset 3650 - No access to config

I stupidly wrote a config to startup that meant I have no access to the config anymore. I tried factory resetting the node by using the physical button on the front - Holding it in for three seconds until the lights flash, then keeping it held in for...

Resolved! Retrieve Config file from locked out SG200

Hello,I have a few SG200s, mostly one at each building. There is one that I suddenly can't log into - "invalid user name or password"*. With no COM port, it sounds like I don't have many options other than factory reset. Right? The basic re-conf...

Resolved! How to setup VLANs between SG500, SG300 switches

Hi all, I am trying to setup a VLAN on my network which will be for servers and other resources (not clients) and I am having quite a bit of trouble getting it to work. I have setup VLANs before with Dell PowerConnect and 3Com switches but we have si...

SG220 Switches compatibility for MGBSX1

Below Case 636613351 Owner on Cisco Side told me that the MGBSX1 is no longer supported and the documentation is incorrect !CISCO.COM ID:manfred@edv24.atSUPPORT CASE:636613351SUPPORT CASE TITLE:AU-SG220 SFP MGBSX1 compatibility issuesSEVERITY:3STATUS...

SG220-50P voice help needed

OK, clearly I am missing something, but this is my first time using both VLANs and Voice. I have read so much documentation that my eyes are glazing over. Scenario: Cisco SG220-50P feeding a Sonicwall TZ600 firewall and then out to the internet throu...

SG102-24 connectivity

I'm having problems with my network. We use a single SG102-24 Cisco switch with about 16 ports utilized. The entire network is wired with CAT6 cables. One computer was constantly unable to save files across the network to either of 2 Ready NAS hard d...

Access web interface from Domain PC

I recently setup a small domain for my business and when trying to access the web interface for the SG200 from a client that is in the domain, the switch configuration website has the standard blue background and two input fields, but I can't get any...

SG-200-18 - How To Restore Configuration

So maybe I'm completely missing something but I am unable to figure out how to restore my backed-up configuration file to my switch.The SG-200 series doesn't support FTP or TFTP nor does it have a console port and from what I can see, the web GUI onl...

SG200-08 switch NTP not working

Hello,I have an SG200-08 and can't get NTP to work. The relevant lines of my configuration are below:sntp client mode unicastsntp unicast client poll-interval 16sntp server pool.ntp.org enableclock summer-time recurring USA zone EDTclock timezone -5...

SMB and 3850

hello ??can anyone guide that what is the trunk configuration between SMB and 3850.I also need to configure voice and data vlans .

Switches - Small Business

Forum Posts