cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements
Join Customer Connection to register!
216
Views
5
Helpful
3
Replies
imranbhatti22006
Beginner

2960 X 48LPD L not switching, license issue?

Hi, 

 

I've 3 Switches WS-2960X-48LPD-L PoE . All of them have amber light on system after boot, 

Vlan 1 is getting IP from DHCP but other ports once connected to host doesn't communicate over to dhcp. 

I tried static IP also but its not working, there's some serious issue with these switches, 

 

I checked about license, but Cisco says no license is needed? 

Here're details, 

 

 

512K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address : AC:7E:8A:6D:41:00
Motherboard assembly number : 73-16687-04
Power supply part number : 341-0528-01
Motherboard serial number : FOC1830HJ5R
Power supply serial number : LIT1830T01T
Model revision number : G0
Motherboard revision number : B0
Model number : WS-C2960X-48LPD-L
Daughterboard assembly number : 73-14200-03
Daughterboard serial number : FOC1830306K
System serial number : FCW1810A33W
Top Assembly Part Number : 68-100465-01
Top Assembly Revision Number : C0
Version ID : V04
CLEI Code Number : CMMLK00ARD
Daughterboard revision number : A0
Hardware Board Revision Number : 0x12

Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
* 1 52 WS-C2960X-48LPD-L 15.2(2)E6 C2960X-UNIVERSALK9-M

------------------------------------------------------------------------------------------------------

cisco WS-C2960X-48LPD-L (APM86XXX) processor (revision A0) with 524288K bytes of memory.
Processor board ID FCW1836A32L
Last reset from power-on
1 Virtual Ethernet interface
1 FastEthernet interface
50 Gigabit Ethernet interfaces
2 Ten Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.

512K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address : 00:8E:73:24:85:00
Motherboard assembly number : 73-14187-04
Power supply part number : 341-0527-01
Motherboard serial number : FOC1820G87N
Power supply serial number : DCB1822A54R
Model revision number : A0
Motherboard revision number : A0
Model number : WS-C2960X-48LPD-L
Daughterboard assembly number : 73-14200-03
Daughterboard serial number : FOC1826G87K
System serial number : FCW1836A32L
Top Assembly Part Number : 800-38002-01
Top Assembly Revision Number : A0
Version ID : V01
CLEI Code Number : CMMLK00ARA
Daughterboard revision number : A0
Hardware Board Revision Number : 0x12


Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
* 1 52 WS-C2960X-48LPD-L 15.2(2)E6 C2960X-UNIVERSALK9-M

------------------------------------------------------------------------------------------------------

512K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address : 00:56:2B:90:22:00
Motherboard assembly number : 73-14187-04
Power supply part number : 341-0527-01
Motherboard serial number : FOC1827M78H
Power supply serial number : DCB1830K67F
Model revision number : A0
Motherboard revision number : A0
Model number : WS-C2960X-48LPD-L
Daughterboard assembly number : 73-14200-03
Daughterboard serial number : FOC1831D23A
System serial number : FCW1836A36M
Top Assembly Part Number : 800-38002-01
Top Assembly Revision Number : A0
Version ID : V01
CLEI Code Number : CMMLK00ARA
Daughterboard revision number : A0
Hardware Board Revision Number : 0x12


Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
* 1 52 WS-C2960X-48LPD-L 15.2(4)E6 C2960X-UNIVERSALK9-M

 

 

 

 

 

 

3 REPLIES 3
Georg Pauwen
VIP Expert

Hello,

 

when you reload/reboot the switch, what is the output on the console ? Can you post that ?

Leo Laohoo
VIP Community Legend


@imranbhatti22006 wrote:

All of them have amber light on system after boot, 


Post the complete output to the following command: 

sh post
balaji.bandi
VIP Expert

3 Switches WS-2960X-48LPD-L PoE   - is this working before - any power Loss ? 

 

Did AMBER  LED  on all interface ports - if you get a chance connect one of the switch console port reboots and post complete output.

 



BB


*** Rate All Helpful Responses ***