Hi, QoS expert
I tried to put QoS in a WS-C3560CG-8TC-S version 12.2(55)EX2.
It shows 0 traffic in class-map.
Here is the config
My question is why I can not see the traffic via class-map?
it should in the default Q if incorrect mark.
I erased the config and config with the autoQoS, shows the same result.
Let me know and thanks.
*******************
class-map match-any VoIP
description Voice IP Phone RTP
match access-group 157
class-map match-any WEB
description Internal Web, SSL Web, DNS query, Pinnacle
match access-group 153
!
policy-map QOSMARK
class VoIP
set dscp ef
class WEB
set dscp cs3
class class-default
set dscp default
access-list 153 remark * WEB class (IP Precedence 2)
access-list 153 remark - HTTP traffic (within local only)
access-list 153 permit tcp any any eq www
access-list 153 permit tcp any eq www any
access-list 153 remark - SSL Web traffic
access-list 153 permit tcp any any eq 443
access-list 153 permit tcp any eq 443 any
access-list 157 remark * VoIP class (IP Precedence 5)
access-list 157 remark - voice RTP packets
access-list 157 permit udp any any range 16384 32767
access-list 157 permit udp any range 16384 32767 any
interface GigabitEthernet0/8
switchport access vlan 874
switchport mode access
service-policy input QOSMARK
*******************
here is the result
Switch#show policy-map interface g0/8
GigabitEthernet0/8
Service-policy input: QOSMARK
Class-map: VoIP (match-any)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: access-group 157
0 packets, 0 bytes
5 minute rate 0 bps
Class-map: WEB (match-any)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: access-group 153
0 packets, 0 bytes
5 minute rate 0 bps
Class-map: class-default (match-any)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: any
0 packets, 0 bytes
5 minute rate 0 bps
Switch#
Switch#show int g0/8
GigabitEthernet0/8 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is a456.3091.5488 (bia a456.3091.5488)
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 1000Mb/s, media type is 10/100/1000BaseTX
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:03, output 00:00:01, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 1000 bits/sec, 1 packets/sec
5 minute output rate 5000 bits/sec, 7 packets/sec
3111 packets input, 311714 bytes, 0 no buffer
Received 91 broadcasts (79 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 79 multicast, 0 pause input
0 input packets with dribble condition detected
22156 packets output, 11306901 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped out
Switch#
