3650 switch always reboots to initial configuration dialog prompt

[JohnW63]

A 3650 switch I am setting up does not retain the running config and goes to the setup dialog prompt. I have gone into terminal and used the "switch_ignore_startup_cfg=0" command with no effect. I even tried setting the register to the hex value, but I believe that is just for routers. I install a running config and copy it to the start-up config every time. Do I have to go into the ROMMON to use the ignore command properly ?  This isn't the first switch I've had this issue with a switch. 

[Reza Sharifi]

Can you post the output of "sh ver"?

HTH

[JohnW63]

Switch#sh ver

Cisco IOS Software, IOS-XE Software, Catalyst L3 Switch Software (CAT3K_CAA-UNIVERSALK9-M), Version 03.06.04.E RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2016 by Cisco Systems, Inc.

Compiled Sat 13-Feb-16 03:45 by prod_rel_team

Cisco IOS-XE software, Copyright (c) 2005-2015 by cisco Systems, Inc.

All rights reserved.  Certain components of Cisco IOS-XE software are

licensed under the GNU General Public License ("GPL") Version 2.0.  The

software code licensed under GPL Version 2.0 is free software that comes

with ABSOLUTELY NO WARRANTY.  You can redistribute and/or modify such

GPL code under the terms of GPL Version 2.0.

(http://www.gnu.org/licenses/gpl-2.0.html) For more details, see the

documentation or "License Notice" file accompanying the IOS-XE software,

or the applicable URL provided on the flyer accompanying the IOS-XE

software.

ROM: IOS-XE ROMMON

BOOTLDR: CAT3K_CAA Boot Loader (CAT3K_CAA-HBOOT-M) Version 3.56, RELEASE SOFTWARE (P)

Switch uptime is 1 hour, 4 minutes

Uptime for this control processor is 1 hour, 7 minutes

System returned to ROM by reload

System image file is "flash:packages.conf"

Last reload reason: Reload command

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

License Level: Ipbase

License Type: Permanent

Next reload license Level: Ipbase

cisco WS-C3650-48PD (MIPS) processor with 4194304K bytes of physical memory.

Processor board ID FDO2032E39K

1 Virtual Ethernet interface

50 Gigabit Ethernet interfaces

2 Ten Gigabit Ethernet interfaces

2048K bytes of non-volatile configuration memory.

4194304K bytes of physical memory.

252000K bytes of Crash Files at crashinfo:.

1611414K bytes of Flash at flash:.

0K bytes of Dummy USB Flash at usbflash0:.

0K bytes of  at webui:.

Base Ethernet MAC Address          : 00:a2:ee:05:b7:00

Motherboard Assembly Number        : 73-15897-05

Motherboard Serial Number          : FDO20330KVC

Model Revision Number              : N0

Motherboard Revision Number        : A0

Model Number                       : WS-C3650-48PD

System Serial Number               : FDO2032E39K

Switch Ports Model              SW Version        SW Image              Mode

------ ----- -----              ----------        ----------            ----

*    1 52    WS-C3650-48PD      03.06.04.E        cat3k_caa-universalk9 INSTALL

Configuration register is 0x142 (will be 0x102 at next reload)

[Reza Sharifi]

Configuration register is 0x142 (will be 0x102 at next reload)

Can you change the config register to 0x102, save and reboot?

HTH

[balaji.bandi · Accepted solution]

conf t

no system ignore startupconfig switch all

!

config-register 0x102

write mem

!

end

#reload

[JohnW63]

That worked. 

How does ..."no system ignore startupconfig switch all" differ from the command, "switch_ignore_startup_cfg=0" ?

John

[balaji.bandi]

One you issue on ROMMON Mode, One you using in the config mode.