03-15-2012 07:41 AM - edited 03-07-2019 05:35 AM
Hi,
Have an issue with IOS upgrade. As am running IOS I do not need bootldr; so under sh boot - it says no bootldr set
Have IOS c6sup22-jk2o3sv-mz.121-27b.E4.bin" in bootflash and s222-adventerprisek9_wan-mz.122-18.SXF11.bin on disk0
Am forcing switch to boot new IOS via command boot system disk0:s222-adventerprisek9_wan-mz.122-18.SXF11.bin
So what happens - it boots to the point where it says - Changing console ownership to route processor
and then crashes ??
Have another 6500 where made it run but when you reload it - it is no booting , it gets to rommon and sits there
When you issue boot disk0: it then boots up
I do have command in config where it says boot system disk0:s222.......... but for some reason seems not working ?
Highly appreciate any help
Thanks
Arunas
03-15-2012 08:55 AM
*** System received a Software forced crash ***
signal= 0x17, code= 0x41e20000, context= 0x41e45ef4
PC = 0x402d238c, Cause = 0x1820, Status Reg = 0x34018002
03-15-2012 09:18 AM
Hello Arunas,
can you please add the whole logs appearing from the time you are trying to load the image untill it goes into rommon again.
Best Regards,
Zaid
03-15-2012 10:46 AM
Core-2#sh boot
BOOT variable = disk0:s222-adventerprisek9_wan-mz.122-18.SXF17b.bin,1
CONFIG_FILE variable does not exist
BOOTLDR variable =
Configuration register is 0x2102
Standby is not up.
Core-2#sh run | i boot
boot system flash disk0:s222-adventerprisek9_wan-mz.122-18.SXF17b.bin
Core-2#reload
Proceed with reload? [confirm]
*Mar 15 14:01:24: %SYS-5-RELOAD: Reload requested
*Mar 15 14:01:27: %OIR-SP-6-CONSOLE: Changing console ownership to switch processor
***
*** --- SHUTDOWN NOW ---
***
*Mar 15 14:01:30: %SYS-SP-5-RELOAD: Reload requested
*Mar 15 14:01:30: %OIR-SP-6-CONSOLE: Changing console ownership to switch processor
System Bootstrap, Version 7.1(1)
Copyright (c) 1994-2001 by cisco Systems, Inc.
c6k_sup2 processor with 131072 Kbytes of main memory
rommon 1 > boot disk0:s222-adventerprisek9_wan-mz.122-18.SXF17b.bin (entering full name as file is not the first on disk0)
Self extracting the image... [OK]
Self decompressing the image : ################################################################################# [OK]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) s222_sp Software (s222_sp-ADVENTERPRISEK9_WAN-M), Version 12.2(18)SXF17b, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by cisco Systems, Inc.
Compiled Tue 15-Mar-11 18:47 by ccai
Image text-base: 0x40101040, data-base: 0x4113D680
00:00:04: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
00:00:04: %PFREDUN-6-ACTIVE: Initializing as ACTIVE processor
00:00:07: %SYS-SP-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
00:00:04: %SYS-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.
00:00:07: %OIR-SP-6-CONSOLE: Changing console ownership to route processor
System Bootstrap, Version 12.1(11r)E1, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2002 by cisco Systems, Inc.
Cat6k-MSFC2 platform with 131072 Kbytes of main memory
00:00:22: %SYS-SP-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
00:00:22: %SYS-SP-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.
00:00:22: %OIR-SP-6-CONSOLE: Changing console ownership to switch processor
*** System received a Software forced crash ***
signal= 0x17, code= 0x41e20000, context= 0x41e4e294
PC = 0x402d238c, Cause = 0x1820, Status Reg = 0x34018002
rommon 2 >
03-15-2012 10:18 AM
Do you have enough nvram to run that new image? That image is a "lot" bigger than the one you are replacing and probably takes more nvram . Need at least 256 meg of nvram to run the SXF train.
03-15-2012 10:58 AM
Glen, I guess you were right
Is it right - am not even having 1MB of it ??
APH-Core-2-Mat#sh file systems
File Systems:
Size(b) Free(b) Type Flags Prefixes
64266240 12075008 disk rw disk0:
* - - flash rw slot0: flash: sup-slot0:
31981568 5195796 flash rw sup-bootflash:
26247326 0 opaque ro sup-microcode:
0 34330492 opaque wo sup-image:
129004 123588 nvram rw const_nvram:
- - opaque rw null:
- - opaque rw system:
- - network rw tftp:
391160 346325 nvram rw nvram:
31981568 31981568 flash rw bootflash:
- -