10-02-2017 05:59 AM - edited 03-08-2019 12:14 PM
Hi,
I am running a VSS consisting of two 6509-E with Sup720 MSFC3. The IOS is a 15.1(2)SY2. I tried to upgrade to 15.1(2)SY5. According to the ISSU compatibility matrix this should work. I did a "issu loadversion", and as soon as the second supervisor came up with the new software the active sup logs:
%ISSU-SW2_SPSTBY-3-NOT_FIND_UNDER_SESSION: Can not find control block under session group for msg type(117) under receive transform session(652).
%ISSU_ERROR-SW2_SPSTBY-3-TRANSFORM_FAILED: ISSU VS Power Client(6056): receive transformation failed (ISSU_RC_MSG_TYPE_NOT_FOUND)
%ISSU_ERROR-SW2_SPSTBY-3-MSG_MTU: ISSU VS Power Client(6056): Client failed to get mtu for message 118 (ISSU_RC_NEGO_RESULT_NOT_FOUND)
%ISSU_ERROR-SW2_SPSTBY-3-TRANSFORM_FAILED: ISSU VS Power Client(6056): transmit transformation failed (ISSU_RC_MSG_TYPE_NOT_FOUND)
%ISSU-SW1_SP-3-INCOMPATIBLE_PEER_UID: Setting image (s72033_sp-IPSERVICESK9-M), version (15.1(2)SY5) on peer uid (517) as incompatible
%ISSU_PROCESS-SW1_SP-4-ABORT_ISSU: Service Incompatibility - Aborting the ISSU process
%ISSU_PROCESS-SW1_SP-3-ABORT: Abortversion still in progress, please wait ...
%ISSU_PROCESS-SW1_SP-3-ABORT: Resetting Standby shortly
After that the secondary sup reboots the old ios and the issu is cancelled.
Any ideas?
10-02-2017 06:39 AM - edited 10-02-2017 06:39 AM
Hi,
Did you verify that it is actually going to work?
See this document.
HTH
10-02-2017 08:54 AM
This was the output of "show switch virtual redundancy" before the upgrade. It was in SSO mode, hot standby.
#show switch virtual red
My Switch Id = 1
Peer Switch Id = 2
Last switchover reason = user forced
Configured Redundancy Mode = sso
Operating Redundancy Mode = sso
Switch 1 Slot 5 Processor Information :
-----------------------------------------------
Current Software state = ACTIVE
Uptime in current state = 2 years, 42 weeks, 5 days, 22 hours, 56 minutes
Image Version = Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICESK9-M), Version 15.1(2)SY2, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Wed 26-Feb-14 16:36 by prod_rel_team
BOOT = sup-bootdisk:s72033-ipservicesk9-mz.151-2.SY2.bin,1;bootdisk:s72033-ipservicesk9-mz.151-2.SY2.bin,12;
Configuration register = 0x2102
Fabric State = ACTIVE
Control Plane State = ACTIVE
Switch 2 Slot 5 Processor Information :
-----------------------------------------------
Current Software state = STANDBY HOT (switchover target)
Uptime in current state = 2 years, 42 weeks, 5 days, 22 hours, 34 minutes
Image Version = Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICESK9-M), Version 15.1(2)SY2, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Wed 26-Feb-14 16:36 by prod_rel_team
BOOT = sup-bootdisk:s72033-ipservicesk9-mz.151-2.SY2.bin,1;bootdisk:s72033-ipservicesk9-mz.151-2.SY2.bin,12;
Configuration register = 0x2102
Fabric State = ACTIVE
Control Plane State = STANDBY
10-04-2017 08:05 AM
I checked once more according to the document you sent and found no problems in the config:
wiss#show redundancy
Redundant System Information :
------------------------------
Available system uptime = 4 years, 1 week, 3 days, 6 hours, 27 minutes
Switchovers system experienced = 8
Standby failures = 0
Last switchover reason = user forced
Hardware Mode = Duplex
Configured Redundancy Mode = sso
Operating Redundancy Mode = sso
Maintenance Mode = Disabled
Communications = Up
Current Processor Information :
-------------------------------
Active Location = slot 1/5
Current Software state = ACTIVE
Uptime in current state = 33 minutes
Image Version = Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICESK9-M), Version 15.1(2)SY2, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Wed 26-Feb-14 16:36 by prod_rel_team
BOOT = bootdisk:s72033-ipservicesk9-mz.151-2.SY2.bin,12;bootdisk:s72033-ipservicesk9-mz.151-2.SY4.bin,12;
Configuration register = 0x2102
Peer Processor Information :
----------------------------
Standby Location = slot 2/5
Current Software state = STANDBY HOT
Uptime in current state = 27 minutes
Image Version = Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICESK9-M), Version 15.1(2)SY2, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Wed 26-Feb-14 16:36 by prod_rel_team
BOOT = bootdisk:s72033-ipservicesk9-mz.151-2.SY2.bin,12;bootdisk:s72033-ipservicesk9-mz.151-2.SY4.bin,12;
Configuration register = 0x2102
wiss#show issu state detail
The system is configured to be upgraded in in-tandem mode.
Platform has forced upgrade to in-tandem mode.
2 supervisor nodes are found to be online.
Summary: the system will be upgraded in in-tandem mode.
Slot = 1/5
RP State = Active
ISSU State = Init
Boot Variable = bootdisk:s72033-ipservicesk9-mz.151-2.SY2.bin,12;bootdisk:s72033-ipservicesk9-mz.151-2.SY4.bin,12;
Operating Mode = sso
ISSU Sub-State = No Upgrade Operation in Progress
Starting Image = N/A
Target Image = N/A
Current Version = bootdisk:s72033-ipservicesk9-mz.151-2.SY2.bin
Slot = 2/5
RP State = Standby
ISSU State = Init
Boot Variable = bootdisk:s72033-ipservicesk9-mz.151-2.SY2.bin,12;bootdisk:s72033-ipservicesk9-mz.151-2.SY4.bin,12;
Operating Mode = sso
ISSU Sub-State = No Upgrade Operation in Progress
Starting Image = N/A
Target Image = N/A
Current Version = bootdisk:s72033-ipservicesk9-mz.151-2.SY2.bin
I attached the logs from both supervisors.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: