65xx-E and 45xx-E Power

[davidhuynh5]

Does any know the command to determine if the PS are in combined or redundant mode on both the 65xx and 45xx chasis?

Thanks in advance.

[Reza Sharifi]

Try

sh power

http://www.cisco.com/en/US/docs/ios-xml/ios/fundamentals/command/show_monitor_permit_list_through_show_process_memory.html#GUID-C3A4D96B-40CB-4CDF-9909-A5CE22E38834

HTH

[dominic.caron]

Hi,

On the 6500, the command "sh power" will tell you right away.

system power redundancy mode = redundant

system power total =     2671.20 Watts (63.60 Amps @ 42V)

system power used =      1463.70 Watts (34.85 Amps @ 42V)

system power available = 1207.50 Watts (28.75 Amps @ 42V)

                        Power-Capacity PS-Fan Output Oper

PS   Type               Watts   A @42V Status Status State

---- ------------------ ------- ------ ------ ------ -----

1    WS-CAC-6000W       2671.20 63.60  OK     OK     on

2    WS-CAC-6000W       2671.20 63.60  OK     OK     on

                        Pwr-Allocated  Oper

Fan  Type               Watts   A @42V State

---- ------------------ ------- ------ -----

1    WS-C6509-E-FAN      210.00  5.00  OK

                        Pwr-Requested  Pwr-Allocated  Admin Oper

Slot Card-Type          Watts   A @42V Watts   A @42V State State

---- ------------------ ------- ------ ------- ------ ----- -----

1    WS-X6716-10GE       457.80 10.90   457.80 10.90  on    on

5    VS-S720-10G         338.10  8.05   338.10  8.05  on    on

6    WS-X6716-10GE       457.80 10.90   457.80 10.90  on    on

system auxiliary power mode = off

system auxiliary power redundancy operationally = non-redundant

system primary connector power limit =   10920.00 Watts (260.00 Amps @ 42V)

system auxiliary connector power limit = 10500.00 Watts (250.00 Amps @ 42V)

system primary power used =              1463.70 Watts (34.85 Amps @ 42V)

system auxiliary power used =            0 Watt

On the cat 4500, you have to use some déduction...I have two 4200w power supply and I have 8400w available...

Power                                             Fan      Inline

Supply  Model No          Type       Status       Sensor   Status

------  ----------------  ---------  -----------  -------  -------

PS1     PWR-C45-4200ACV   AC 4200W   good         good     good

PS1-1                         220V   good

PS1-2                         220V   good

PS2     PWR-C45-4200ACV   AC 4200W   good         good     good

PS2-1                         220V   good

PS2-2                         220V   good

Power supplies needed by system    : 2

Power supplies currently available : 2

Power Summary                      Maximum

(in Watts)              Used     Available

----------------------   ----     ---------

System Power (12V)        716        2200

Inline Power (-50V)       968        6200

Backplane Power (3.3V)      0          40

----------------------   ----     ---------

Total                    1684 (not to exceed Total Maximum Available = 7600)

Power Measurement    Inline Power (-50V)

(in Watts)             (+/- 50Watts)

------------------   -------------------

PS1                         350

PS2                         150

------------------   -------------------

Total                       500

The best way is to do a show run and look the power redundancy-mode combined command. If it's not there, its the default of redundant.