cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1323
Views
0
Helpful
1
Replies

Ask for help :( "%ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/17: Power given, but Power Controller does not report Power Good"

sunsteel7378
Level 1
Level 1


This question is used a translator.... 


Current conditions 
 - SW1 ----- Power injector ------ AP(cisco is not another model)
 - Port, AP, Power injector, Switch <-> Injector UTP cable  Problems occur even after replacement
 - Power injector <->AP UTP canle No exchange
 - Poe was OFF the function. This is because it is being used for Power Injector. -> Do not generate failure logs
 - But even if another AP is turned ON POE function, no error messages.

SW1#show logging (5 mins cycle persists)
May  4 10:37:32.527: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/17: Power given, but Power Controller does not report Power Good
May  4 10:37:42.556: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/17, changed state to down
May  4 10:37:43.562: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/17, changed state to down
May  4 10:37:50.032: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/17, changed state to up
May  4 10:37:52.046: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/17, changed state to up
May  4 10:38:03.238: %ILPOWER-7-DETECT: Interface Gi1/0/17: Power Device detected: IEEE PD

 


SW1#show cable-diagnostics tdr interface gi 1/0/17    <----- Issues AP         
TDR test last run on: May 04 10:49:14

Interface Speed Local pair Pair length        Remote pair Pair status
--------- ----- ---------- ------------------ ----------- --------------------
Gi1/0/17  1000M Pair A     84   +/- 10 meters Pair B      Normal              
                            Pair B     84   +/- 10 meters Pair A      Normal              
                            Pair C     84   +/- 10 meters Pair D      Normal              
                            Pair D     84   +/- 10 meters Pair C      Normal              

SW1#show cable-diagnostics tdr interface gigabitEthernet 1/0/18    <--------- Normal AP
TDR test last run on: May 04 11:01:04

Interface Speed Local pair Pair length        Remote pair Pair status
--------- ----- ---------- ------------------ ----------- --------------------
Gi1/0/18  1000M Pair A     92   +/- 10 meters Pair B      Normal              
                           Pair B     92   +/- 10 meters Pair A      Normal              
                           Pair C     92   +/- 10 meters Pair D      Normal              
                           Pair D     92   +/- 10 meters Pair C      Normal  

SW1#show cable-diagnostics tdr interface gigabitEthernet 1/0/1   <--------- Normal AP
TDR test last run on: May 04 11:01:56

Interface Speed Local pair Pair length        Remote pair Pair status
--------- ----- ---------- ------------------ ----------- --------------------
Gi1/0/1   1000M Pair A     79   +/- 10 meters Pair B      Normal              
                           Pair B     79   +/- 10 meters Pair A      Normal              
                           Pair C     79   +/- 10 meters Pair D      Normal              
                           Pair D     79   +/- 10 meters Pair C      Normal              

 

 

SW1#show power inline    <-------- (Check every 5 seconds)

Module   Available     Used     Remaining
               (Watts)     (Watts)    (Watts) 
------   ---------   --------   ---------
1              370.0      200.2       169.8
Interface Admin  Oper       Power     Device                           Class   Max
                                            (Watts)                            
--------- ------ ---------- ------- ------------------- ----- ----
SW1#show power inline | in 17
Gi1/0/17  auto     off        0.0                 n/a                               n/a   30.0 
SW1#show power inline | in 17
Gi1/0/17  auto     on         15.4             Ieee PD                         0     30.0 
SW1#show power inline | in 17
Gi1/0/17  auto     on         15.4             Xirrus XR2426, 1.0G     0     30.0 
SW1#show power inline | in 17
Gi1/0/17  auto     faulty     0.0              n/a                                 n/a   30.0 
SW1#show power inline | in 17
Gi1/0/17  auto     off        0.0                n/a                                  n/a   30.0

 
1 Reply 1

Leo Laohoo
Hall of Fame
Hall of Fame

Plug the Xirrus AP directly to the switch port and see if the logs go away or not.

Review Cisco Networking products for a $25 gift card